Sanyo CE42LH2DPB Car Video System User Manual


  Open as PDF
of 33
 
6
Step: 1 Mains Connection
N&RQQHFWWKHGLVSOD\XQLWWR9*$%1&DQG6FDUWFRQ-
nector as required.
1. Connect the in-line power connector to the Mains Inlet as shown
above.
2. Connect the power cord of the LCD monitor to a suitable wall outlet.
As this product does not have a mains On/Off switch, please
ensure your mains plug is easily accessible.
The LCD monitor is prepared for a mains voltage AC100 ~ 240V,
50Hz/60Hz. To completely switch off the mains, or when the
display unit is not to be used for an extended period of time, it is
advisable to disconnect the power cord from the power outlet.
Please use the correct mains lead supplied with the set for your
area.
3. Warning:
To prevent injury, the unit must be securely attached to
the wall in accordance with the installation instructions.
WARNING! High voltages are used in the
RSHUDWLRQRIWKLVVHW5HIHUVHUYLFHWRTXDOL¿HG
service personnel.
Step: 2 Connections
NINPUT selection
7RVZLWFKHLWKHU$95*%$9$93&'9,RU1HWZRUNE\SUHVV-
ing the INPUT button on your remote control repeatedly.
1. AV1
SCART connection/CVBS/RGB/S-VIDEO.
2. RGB
TTL input (5V RGB signals) into SCART terminal.
<3E3U5*%+9FRQQHFWLRQ$9
Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting
in Set up menu (see page 10). You can connect your DVD player
to the Y, Pb, Pr terminals instead of using a scart lead. This can
VXSSRUWKLJKGH¿QLWLRQLQDQDORJXHFRPSRQHQWIRUP5*%+9FDQ
be used as a PC input via the BNC terminals. Both options support
a large range of resolutions (page 17). AV2-OUT can be used to
output the incoming AV2 signal to the other monitor.
4. AV3
Composite (CVBS) signal input.
AV3-OUT can be used to output the incoming AV3 signal to the
other monitor.
5. DVI-D (Digital Video Interface)
DVI-D supports a large range of resolutions as shown on page 17.
6. PC connection
PC input (PC-IN D-SUB). This input supports a large range of reso-
lutions as shown page 17. Audio can be connected via the 3.5mm
PC-AUDIO IN.
7. External Speaker
Output the audio signal from AV1, AV2, AV3, PC and DVI.
7KHVSHDNHULPSHGDQFHLVRKPV
8. AV2 / DVI AUDIO IN
Connect the audio output (stereo) from a computer or video equip-
ment connected AV2 or DVI.
9. Monitor Audio OUT
7KLVWHUPLQDOVRXWSXW¿[HGOHYHOIURP$8',2,1
10. RS232C IN/OUT
:KHQWKHPRQLWRULVFRQWUROOHGE\DFRPSXWHUFRQQHFWWRWKLVMDFN
with serial control cable.
You can connect to another monitor with RS232C OUT.
:KHQ\RXFRQQHFW3&ZLWK56&VHOHFW³21´DW1HWZRUN
standby in Installation mode.
If it is selected “OFF”, RS232C terminals do not functional. Also
select push button to “SERIAL PORT”.
INSTALLATION
7KLV¿JXUHLV&(/+:3
AC Mains Outlet
LD-Net
GB GB
 previous next