Titan Tool 515-592 Manual

Open as PDF

next previous

Important Safety Information · Read all safety information before

operating the equipment. SAVE THESE INSTRUCTIONS.

• Place paint pump at least 20 feet from the spray object

in a well ventilated area (add more hose if necessary).

Flammable vapors are often heavier than air. Floor area

must be extremely well ventilated.

• The equipment and objects in and around the spray area

must be properly grounded to prevent static sparks.

• Keep area clean and free of paint or solvent containers,

rags and other ammable materials.

• Use only conductive or grounded high pressure uid hose.

Gun must be grounded through hose connections.

• Power cord must be connected to a grounded circuit.

• Always ush unit into a separate metal container, at low

pump pressure, with spray tip removed. Hold gun rmly

against side of container to ground container and prevent

static sparks.

• Follow the material and solvent manufacturer’s warnings

and instructions. Know the contents of the paints and

solvents being sprayed. Read all Material Safety Data

Sheets (MSDS) and container labels provided with

the paints and solvents. Follow the paint and solvent

manufacturer’s safety instructions.

• Use extreme caution when using materials with

a ashpoint below 70ºF (21ºC). Flashpoint is the

temperature that a uid can produce enough vapors to

ignite.

• Plastic can cause static sparks. Never hang plastic to

enclose a spray area. Do not use plastic drop cloths when

spraying ammable materials.

• Use lowest possible pressure to ush equipment.

• Do not spray onto pump assembly.

Grounding Instructions

Proper grounding is important. This applies to gas,

electric and air powered models. The passage of

some materials through the nylon fluid hose will

build up a static electric charge, which is

discharged, could ignite solvent vaport present and

create an explosion.

Grounding the Pump

Be sure the PowrTex 15:1 system is grounded. All Titan units

are equipped with a grounding lug. A Grounding Clamp, Part No.

101-208 and Ground Wire, Part No. 101-212 should be used to

connect the unit to a true earth ground. These accessories can

be ordered from your local distributor.

Loosen the grounding screw. Insert one end of the grounding

wire to a true earth ground. Check local electrical regulations to

detailed grounding instructions.

Table of Contents

Specications ........................................................................... 3

General Description ................................................................. 3

PowrTex 15:1 Assemblies ....................................................... 4

Pump assembly ................................................................... 4

Pole gun assembly .............................................................. 4

Setup instructions ................................................................ 4

Fluid Pump Assemblies ........................................................... 5

Service instructions ............................................................. 5

Air Motor Assembly.................................................................. 6

Service instructions ............................................................. 7

StediFlo™ Air Control Assembly ............................................ 8

Air valve assembly .............................................................. 8

Material valve assembly ...................................................... 8

Automatic lubricator............................................................. 8

Installation instructions ........................................................ 8

Cleanout procedure ............................................................. 9

Operation instructions ......................................................... 9

StediFlo™ air valve service kit .......................................... 10

Material valve service kit ................................................... 10

StediFlo™ valve parts list .................................................. 10

Material valve parts list ...................................................... 11

Pole Guns, mastic, air atomizing, 701 Series ...................... 12

Operation........................................................................... 13

Maintenance ...................................................................... 13

Specications .................................................................... 13

Misc. Parts Listings ................................................................ 14

Cart assembly ................................................................... 14

Accessories ............................................................................ 14

Troubleshooting ..................................................................... 15

Warranty .................................................................................. 16

Specications

PowrTex 15:1 Heavy Materials Sprayer

Gallons per minute (GPM) .............3.0 (11.1 LPM)

Maximum pressure ........................ 1500 PSI (103.4 BAR)

Mounting:

Cart Mount ....................... Cart

Drum Mount ..................... Drum Clamp

Supply:

Cart Mount ....................... 5 gallon (19 liters)

Drum Mount ..................... 55 gallon (208 liters)

Ratio ......................................... 15:1

Compressor Requirements............ 50 CFM @ 90 PSI

Surge Control ................................ StediFlo™

Cycles Per Gallon ..........................20 (5 per liter)

Pole Gun........................................ 2 ft (61 meters)

Hose Length .................................. 50 ft (15.2 meters) standard

equipment and 200 ft (61m)

maximum hose length

General Description

Titan PowrTex model 15:1 is suitable for most textures and

mastics. The slow stroking hard chrome pump resists wear from

coarse aggregates. Titan’s StediFlo™ control minimizes pulsing

and prevents material ow until atomizing air is turned on.