Titan Tool 581-085 Manual

Open as PDF

next previous

English

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

NOTE: Refer to the Parts List section in this manual for part

identication.

Replacing/Servicing the Seal Assembly

Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,

theneedleorseatisworn,damaged,ordirtyandmustbereplacedor

cleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheuidhosefromthegun.

 2. Removethetipandtipguard.

 3. Withthetriggerdepressed,removethediffuserfromthefrontof

thegun.

 4. Removethelocknut,rearhousing,andretractorpinsfromthe

rearofthegunhead.

 5. Removethesealassemblyfromthefrontofthegunheadby

pushingorgentlytappingatthebackofthesealassembly.

 6. Soaktheremovedpartsintheappropriatesolventandwipe

clean.

 7. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts before

reassembly with a lithium-based grease.

 8. Installthesealassemblyintothefrontofthegunhead.

 9. Installtheretractorpinsintotherearofthegunhead.Slidethe

rearhousingontotheretractorpinsandsecureinpositionwith

thelocknut.

 10. WIththetriggerdepressed,installthediffuserintothefrontofthe

gunheadandtightensecurelywithawrench.

 11. Performthe“AdjustingtheSealAssembly”proceduredescribed

below.

Adjusting the Seal Assembly

Proper adjustment of the seal assembly is essential to

ensure positive shut-off when the trigger is released.

 1. Tightenthelocknutuntiltherearhousingisushagainstthegun

head.

 2. Unscrewthelocknut3/4ofaturn.

NOTE: To check the adjustment of the seal assembly:

1. Move the gun trigger lock to the locked position.

2. Pull the trigger.

With the trigger lock engaged, there should be 1/32” of

movement between the lock nut and the rear housing

while pulling the trigger.

Replacing/Removing the Filter

 1. Pullthebottomofthetriggerguardforwardsothatitcomesloose

fromthehandleassembly.

 2. Loosenandremovethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Slidethenewlter,taperedendrst,intothegunhead.

 5. Makesurethehandlesealisinpositionandthreadthehandle

assemblyintothegunheaduntilsecure.

 6. Snapthetriggerguardbackontothehandleassembly.

Gun Filter Chart

Part

Number

Application Filter

Type

Color of

Filter

Body

500-200-15 Synthetic resin,

enamels, clean

varnishes, stains

azures

Extrafine red

500-200-10 Base coat enamels,

primer enamels,

fillers, marking paints,

textured enamels

Fine yellow

500-200-06 Emulsions,

latex paints,

acrylic paints

Medium white

500-200-03 Filler paints,

large area surfaces

Coarse green

Parts List

Item Part # Description Quantity

1 580-521 Gunhead ..................................................1

 2 580-513 Triggerscrew,short ..................................1

 3 580-071 Triggerassembly,4-ngergun

   (includesitems2and14) .........................1

 4 580-532 Triggerguard ............................................1

 5 580-510 Sealassembly ..........................................1

 6 520-093 Diffuser .....................................................1

 7 651-020 Seal ..........................................................1

 8 661-517 Tipassembly,

   (includesitems7and10) .........................1

 9 661-012 Tipguard .................................................1

 10 651-040 Tipseal .....................................................1

 11 226-001 Locknut ....................................................1

 12 580-003 Rearhousing ............................................1

 13 580-025 Retractorpin .............................................2

 14 580-512 Triggerscrew,long ...................................1

 15 500-200-06 Filter,medium ...........................................1

 16 560-038 Handleseal...............................................1

 17 580-531 Handle ......................................................1

 18 580-530 Swivel .......................................................1

 19 581-078 Triggerassembly,2-ngergun .................1

 20 581-126 Collarassembly,2-ngergun ...................1

  580-533 Handleassembly(includesitems17–18)

  580-534 Gunrepairkit(includesitems5,6,and11)