Filter
Top Products
1010
1010
10
CD CHCD CH
CD CHCD CH
CD CH
AA
AA
A
NGER CONTRNGER CONTR
NGER CONTRNGER CONTR
NGER CONTR
OLOL
OLOL
OL
SS
SS
S
CD CHCD CH
CD CHCD CH
CD CH
AA
AA
A
NGER CONTRNGER CONTR
NGER CONTRNGER CONTR
NGER CONTR
OLOL
OLOL
OL
S / ERRS / ERR
S / ERRS / ERR
S / ERR
OR CODEOR CODE
OR CODEOR CODE
OR CODE
CD CHCD CH
CD CHCD CH
CD CH
AA
AA
A
NGER ERRNGER ERR
NGER ERRNGER ERR
NGER ERR
OR CODEOR CODE
OR CODEOR CODE
OR CODE
If a problem should develop while operating the CD changer, the error code “Err” may appear on the display
panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the
microprocessor control of the changer. If the error code should appear, try ejecting and re-loading the magazine
into the changer. While the magazine is out of the changer, make sure the discs are clean, undamaged, and
loaded correctly (see Owner’s Manual of the CD changer). You may also try activating the Re-Set button cr
on the unit, but this will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty station near you for further
assistance.
Built into this radio are controls to operate an optional
CD changer. Please check with your Rampage/
Audiovox car stereo specialist for recommendations
of the models that will work with this radio.
IMPORTANT: The CD Changer Selector Switch on the
bottom of the chassis must be set to the correct
position to match the type of changer being used with
this radio. The Re-Set button cr should then be pressed
to activate the change of position. If you are not sure of
the correct switch position for your model of CD changer,
please check with your Rampage/Audiovox retailer or
contact us directly at 1-800-645-4994.
NOTE: Switch position for model ACC-30 changer
is "B".
Adjustment of the audio functions (volume, tone,
balance, and fader) for the CD changer operate in the
same manner as they do for radio play. The following
controls will operate the CD changer when it is
installed and connected to this radio. Refer to the
owner’s manual included with the CD changer for
instructions on the installation and correct loading
and use of the CD magazine.
ct CD CHANGER MODE SELECTOR (CD)
PAUSE/PLAY SELECTOR ( II )
During radio, or tape play, press this button to select
operation of the CD changer as shown by “CD-C” and
“CdC” on the display panel. Disc play will begin and
the disc and track number will be shown on the display
panel. If a new magazine has been loaded into the
changer, play will begin from the first track of the first
disc in the magazine. If a magazine was already in the
changer, play will resume from the track on the disc
previously in play.
During CD changer play, pressing this button once will
return to the radio operation. Pressing again will
change to tape play if a tape is loaded in the unit or
back to CD changer if no tape is loaded.
cu & dl DISC SELECT (CD+ & CD-)
These buttons are used to select the desired disc for
play. To advance to a higher number disc, press the
CD+ button cu. To return to a lower number disc,
press the CD- button dl. The number of the disc in
play will be shown on the display panel.
dm TRACK SELECT ( / )
This button is used to quickly select the beginning of
a particular track. With each momentary press of the
Forward Track Select button ( ), the next higher
track number will be selected as shown on the display
panel. Similarly, with each momentary press of the
Backward Track Select button ( ), the next lower
track number will be selected. Pressing and holding
either button will continue to change tracks in the
selected direction.
dn FOWARD SEARCH (SEEK)
High-speed audible search to any forward section of
the disc can be made with this feature. Press and hold
the button to advance rapidly in the forward direction.
do TRACK REPEAT PLAY SELECTOR (RPT)
When the Repeat button is pressed, the “RPT”
indication will appear on the display panel and play of
the selected track will be continually repeated until
the Track Repeat mode is canceled by pressing the
Repeat button again or by activating the Random dq
or Scan dp functions.
dp TRACK SCAN SELECTOR (SCN)
When the Scan button is pressed, the “SCAN” indication
will appear on the display panel, and the first 10
seconds of each track on the disc will be played in
order. When a desired track is reached, press the
Scan button again and play of the selected track will
continue (“SCAN” will disappear from the display
panel). The Track Scan mode will also be canceled
by activating any other disc function (Track Select,
Repeat or Random).
dq RANDOM PLAY SELECTOR (RND)
When the Random button is pressed, the “RND”
indication will appear on the display panel and the
tracks on the disc will be played in a random, shuffled
order. The Track Select buttons dm will also select
tracks in the shuffled order instead of the normal
progression. The Track Shuffle mode can be canceled
by pressing the Shuffle button again or by activating
the Repeat do or Scan dp functions.