Filter
Top Products
E-5
ENGLISH
FRANÇAIS
ESPAÑOL
PORTUGUÊS
Seek Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
FM I ➜ FM II ➜ FT ➜ AM (A) ➜ AT
(FT & AT are Travel Store bands.)
2. Press the
TUN/TRK
to tune in stations. Tuning automati-
cally stops at a broadcasting frequency.
“ SEEK ” indicator will appear on the display window.
When tuned in to FM stereo broadcasting stations, the
“
” stereo signal indicator will appear on the display
window.
Manual Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Press the
TUN/TRK
or
TUN/TRK
for more than 0.5 sec-
ond to activate the manual tuning mode. Press again to
tune in to stations.
“ MANUAL ” indicator will appear on the display window.
After 4 seconds of completing Manual Tuning, the tuning
control will revert to the Seek Tuning mode.
Scan Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
SC/PS
pressed for less than 2 seconds.
The unit will scan the selected band for stations.
“ SCAN ” indicator will appear on the display window. The
unit will stop at each station for 8 seconds, before con-
tinuing to the next station.
Press the
SC/PS
again to stop Scan Tuning and remain
this on the selected frequency.
Tip
While tuning, the pie-shaped signal-strength meter
on the display is lit differently depending on the strength
of the signal. While scanning bands, the pie-shaped sig-
nal-strength meter spins. While playing CD’s, this display
spins also.
Preset Scan Tuning
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
SC/PS
pressed for more than 2 seconds.
“ SCAN ” indicator will appear on the display window.
The unit will scan preset memory for the 12 stations from
the AM/AT band or the 18 stations from the FM I/FM II/
FT bands. The unit will stop at each preset station for 8
seconds, before continuing to the next preset station.
Press the
SC/PS
again to stop Preset Scan Tuning and
remain this on the selected frequency.
Memorizing Stations Automatically (Travel Store)
1. Press the
BND / TS
to select the desired AM or FM band.
2. Hold the
BND / TS
pressed for longer than 2 seconds.
Up to 6 stations with strong signals will be automatically
stored in preset memory for the selected band.
If the radio is in FM I or FM II, it switches to FT. If the
radio is in AM, it switches to AT.
Note
This function is available for FT and AT.
Memorizing Only the Desired Stations
You can store up to 6 stations on each band (18 for FM I, FM
II and FT, 12 for AM and AT) in the order of your choice.
1. Press the
BND / TS
to select the desired band.
2. Press the
TUN/TRK
to tune in stations.
3. Press and hold the desired preset memory button
1
-
6
for about 2 seconds until the frequency indicator
flashes twice.
The number of the pressed preset memory button ap-
pears on the display window.
Note
If when you store another station on the same preset number
button, the previously stored station is replaced with new one.
Receiving the Memorized Stations
1. Press the
BND / TS
to select the desired AM or FM band.
2. Press the
1
➜
6
momentarily.
Local/Distant (LO/DX) Selection
This feature is used to select the signal strength at which the
radio will stop during Seek Tuning.
Press the
MUTE / SENS
for more than 2 seconds to select the
Local setting and only strong (local) stations will be received.
The “ lo ” indicator appears on the display window.
Pressing for more than 2 seconds again will select the Dis-
tant setting and the radio will stop at a wider range of signals,
including weaker more distant stations. The “ lo ” indicator will
go out on the display window. DX is the suggested default
setting.
Radio Reception
AUSTIN CD41 01.3.22, 1:45 PM5