Filter
Top Products
1
VM9311TS
PREPARATION
Congratulations on your purchase of the Jensen VM9311TS
Mobile Multimedia Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen
VM9311TS installed by a reputable installation shop.
Features
DVD
• Compatible formats: DVD-R, DVD-RW, DVD+R,
DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,
VCD and AVI, MPEG1, MPEG2 and JPEG
• Region 1 playback
• 16:9 Aspect ratio - Cinema/Normal/Off
• Front panel DVD control
• High-speed Fast Forward 2X, 4X, 8X, 32X
• Play, Pause, Stop, Slow
• Chapter Up / Down
• Wolfson Microelectronics high performance 24-bit, 192
kHz DAC supports 2-channel "Down-Mix” audio modes
MP3/WMA
• GIGA MP3 - Store up to 999 MP3 files on a DVD
• ID3-tag compatible
• Direct track access
• Play, pause, stop, track up / down
CD
• CD-text compatible
• High-speed audible track search
• Random, repeat A-B, intro
• Play, pause, slow, track up/down
• Last position memory
AM/FM Tuner
• US/Euro/Latin/Asia Tuner
• 30 Station presets (18FM/12AM)
• JENSEN Plus Tuner II
Outboard Media Module
• External Module for connecting XM Radio and iPod
XM Ready
• Requires Optional Terk XMD1000
• Requires Optional Terk XMDJEN100 or Jensen JXMC
• Advanced display shows the artist, song title, and XM
channel and category at a glance
• Direct Channel entry
Made for iPod
• High speed direct connect interface for playlist, artists,
albums, songs, photos and video
• Intuitive iPod interface
• Charges and controls all dockable iPod's
• Requires jLinkcable iPod cable (Sold Separately)
NOTE: Photo and Video access with Gen 5 iPod's
only .
Chassis
• TSD - Touch Screen Display menu control
• 7-inch TFT active-matrix LCD, 336, 960 pixels (1440W X
234H)
• Full automatic motorized TFT LCD flip-out and up
• 16-step TFT LCD tilt adjustment
• 1.0 Din (Single DIN)
• Import ISO/DIN mountable
• Trim Ring Included
• Beep Tone confirmation
• Heat management system - Incorporates forced air-
cooling to keep the chip-sets operating at nominal
temperatures
• Heavy duty galvanized chassis
General
• Full function infrared remote control
• 1 NTSC composite video output for additional screens
• TSD- Touch Screen Display menu control
• High performance audio processor
• Electronic volume, bass, treble, balance and fader
• Bass center frequency adjustment - 60, 80, 100, 130,
150 and 200Hz
• Bass Q factor - 1.0, 1.25, 1.5 and 2.0
• Treble center frequency adjustment - 10, 12.5, 15 and
17kHz
• Subwoofer crossover - 80, 120 and 160Hz
• Subwoofer Phase - 0, 180 degrees
• Subwoofer level - variable
• 100-ohm low impedance preamp outputs - all channels
• 5V Peak / 2V RMS RCA outputs - all channels
• 1-pair Front RCA outputs
• 1-pair Rear RCA outputs
• Single Subwoofer RCA output
• 1-pair Auxiliary RCA A/V inputs
• Flex fader
• Front panel (when screen is closed) high contrast LCD
• Rotary encoder audio control
• Joystick menu navigation
Tools and Supplies
You will need these tools and supplies to install your
VM9311TS:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench
set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt
power supply with proper grounding.
WARNING! Never install this unit where operation
and viewing could interfere with safe driving
conditions.
WARNING! To reduce the risk of a traffic accident
(except when using for rear view video camera)
never use the video display function while driving
the vehicle. This is a violation of federal law.
WARNING! Never disassemble or adjust the unit.
WARNING! To prevent injury from shock or fire,
never expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism
inside this unit, avoid impact to the TFT monitor.
WARNING! Using an improper fuse may cause
damage to the unit and result in a fire.