Jensen VM9411 Car Video System User Manual


 
1
VM9411
PREPARATION
Congratulations on your purchase of the Jensen VM9411
Mobile Multimedia Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen VM9411
installed by a reputable installation shop.
Features
MULTI-ZONE
Allows up front passengers to listen to the radio while rear
passengers listen to a CD, MP3, WMA or watch DVDs
DVD
Compatible formats: DVD-R, DVD-RW, DVD+R,
DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,
VCD and MPEG1, MPEG2 and JPEG
Region 1 playback
16:9 Aspect ratio- Wide / Normal / Cinema
Front panel DVD control
High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X
Play, Pause, Stop, Slow
Chapter Up / Down
MultiZone output 'Kid-Zone'
Wolfson Microelectronics high performance 24-bit, 192
kHz DAC supports 6-channel and 2-channel "Down-Mix”
audio modes
16Mbit high-speed flash memory - 80nS access time
MP3/WMA
GIGA MP3 - Store up to 999 MP3 files on a DVD
ID3-tag compatible
Direct track access
Play, Pause, Stop, Track Up / Down
100 second (MP3), 200 second (WMA) ESP - Electronic
Skip Protection
CD
CD-text compatible
4 second ESP - Electronic Skip Protection
AM/FM Tuner
US/Euro/Latin/Asia Tuner
30 Station presets (18FM/12AM)
JENSEN Plus Tuner II
Outboard Media Module
Input adaptor for TV Tuner, XM Radio and iPod
TV Tuner (Included)
VHF 2-13
UHF 14-69
TV antenna - (3.5mm antenna included)
F-Connector/Coaxial Antenna Input (optional)
XM Ready
Requires optional Terk XMD1000 tuner box
Requires optional Terk XMDJEN100 or Jensen JXMC XM
cables
Advanced display shows the artist, song title, and XM
channel and category at a glance
Direct Channel entry
jLink Ready
Controls and charges all iPod's except "Shuffle"
Displays all text information including category, track
name, artist and channel number
Chassis
7-inch TFT active-matrix LCD - 336,960 pixels (1440W X
234H)
Full automatic motorized TFT LCD flip-out and up
16-step TFT LCD tilt adjustment
Beep Tone confirmation
Heat management system - Incorporates forced air-
cooling to keep the chip-sets operating at nominal
temperatures
Heavy duty galvanized chassis
General
Full function infrared remote control
Limited function infrared "Kid Zone" remote
1 NTSC composite video output for additional screens
OSD- On Screen Display menu control
High performance audio processor
Electronic volume, bass, treble, balance and fader
Bass center frequency adjustment - 60, 80, 100, 130,
150 and 200Hz
Bass Q factor - 1.0, 1.25, 1.5 and 2.0
Treble center frequency adjustment - 10, 12.5, 15 and
17kHz
Subwoofer crossover - 80, 120 and 160Hz
Subwoofer Phase - 0 - 180 degrees
Subwoofer level - variable
100-ohm low impedance preamp outputs - all channels
5V Peak / 2V RMS RCA outputs - all channels
1-pair Front RCA outputs
1-pair Rear / Surround RCA outputs
Single Subwoofer RCA output
Center Channel RCA output
1-pair Headphone / Multi-ZONE RCA outputs
1-pair Auxiliary RCA A/V inputs
Back-up camera input with reverse override
Flex fader
Front panel (when screen is closed) high contrast LCD
Rotary encoder audio control
Joystick menu navigation
Tools and Supplies
You will need these tools and supplies to install your
VM9411:
Torx type, flat-head and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident
(except when using for rear view video camera) never
use the video display function while driving the vehicle.
This is a violation of federal law.
WARNING! Never disassemble or adjust the unit.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Using an improper fuse may cause damage
to the unit and result in a fire.