Filter
Top Products
56
|
DPX504U/ DPX404U/ DPX304
DSP Setup
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- <Car Type Selection> (page 54)
- <Speaker Setting> (page 54)
- <Car Type Fine Adjustments> (page 55)
- <X’Over Setting> (page 56)
- <Manual Equalizer Control> (page 49)
- <Listening Position Selection> (page 50)
- <Listening Position Fine Adjustments> (page 50)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Preset” > “Preset Memory”.
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
When you press the Reset, all the sources will be the setting
value which is registered.
• Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod Equalizer
set in <Preset Equalizer curve Select> (page 49).
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 54).
Display Item Range
“X’Over”
“Front” “FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear” “FC”
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC”
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE”
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
Enter Function setting mode
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“X’Over”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the item you want to set
Operation type Operation
Selects the item. Turn the [VOL] knob.
Adjust each item. Press the [
4
] or [
¢
] button.
Set the value Press the [VOL] knob.
6
Repeat steps 4 to 5 to complete the X’Over
settings.
7
Exit Function setting mode
Press the [ ] button for at least 1 second.
Function of DPX504U