Filter
Top Products
17
ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select
[AUDIO CONTROL]
, then press the
knob.
3 Turn the volume knob to make a selection (see the following table),
then press the knob.
Repeat step
3 until the desired item is selected or activated.
4 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter
[AUDIO CONTROL]
.
2 Press J / K to make a selection, then press ENT IW.
To return to the previous setting item or hierarchy, press
.
Default:
XX
SUB-W LEVEL –15 to +15 (0):
Adjusts the subwoofer output level.
BASS LEVEL –8 to +8 (+6):
Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you
want to adjust.)
MID LEVEL –8 to +8 (+5):
TRE LEVEL
–8 to +8 (0):
PRESET EQ
DRIVE EQ
/
TOP40
/
POWERFUL
/
ROCK
/
POPS
/
EASY
/
JAZZ
/
NATURAL
/
USER
:Selects a preset equalizer suitable to the music genre. (Select
[USER]
to use the customized bass, middle, and treble settings.)
[DRIVE EQ]
is a preset equalizer that reduces noise from the road.
BASS BOOST
LV1
/
LV2
/
LV3
:
Selects your preferred bass boost level.
;
OFF
:
Cancels.
LOUDNESS LV1
/
LV2
:Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level.;
OFF
:Cancels.
SUBWOOFER
SET ON
:Turns on the subwoofer output.;
OFF
:Cancels.
LPF
SUBWOOFER THROUGH
:All signals are sent to the subwoofer.;
85HZ
/
120HZ
/
160HZ
:Audio signals with frequencies lower than 85Hz/ 120Hz/ 160Hz
are sent to the subwoofer.
SUB-W
PHASE REVERSE
(180°)/
NORMAL
(0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than
[THROUGH]
is selected for
[LPF SUBWOOFER]
.)
FADER R15
to
F15
(
0
):Adjusts the rear and front speaker output balance.
BALANCE L15
to
R15
(
0
):Adjusts the left and right speaker output balance.
VOLUME
OFFSET
(Default:
0
)
–8
to
+8
(for AUX) ;
–8
to
0
(for other sources):Presets the volume
adjustment level of each source. (Before adjustment, select the source
you want to adjust.)
SOUND
RECNSTR
(Sound
reconstruction)
ON
:Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF
:Cancels.
•
[SUB-W LEVEL]
/
[SUBWOOFER SET]
/
[LPF SUBWOOFER]
/
[SUB-W PHASE]
is
selectable only if
[SWITCH PREOUT]
is set to
[SUB-W]
.
( 4)
• [SUB-W LEVEL]
/
[LPF SUBWOOFER]
/
[SUB-W PHASE]
is selectable only if
[SUBWOOFER SET]
is set to
[ON]
.
EN_KMM_BT308U_KN_2.indd 17EN_KMM_BT308U_KN_2.indd 17 8/11/2013 3:46:56 PM8/11/2013 3:46:56 PM