Filter
Top Products
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
8
3 GETTING ACQUAINTED
!7!7
!7!7
!7 Frequency control buttons
These buttons control functions related to selecting a
frequency, a VFO, or a memory channel.
• UP/DOWN buttons
Press to step through all Amateur bands
consecutively {page 13} or to step the transceiver
frequency in 1 MHz increments {page 29}. Also
used for making selections from the Menu
{page 16}, and to check Start and End frequencies
for the Scan function {page 43}.
• SPLIT button
Press to use split-frequency operation which allows
a different transmit frequency and receive frequency
{page 23}.
• M/V button
Press to select either Memory or VFO mode
{page 40}.
• TF-SET button
While operating split-frequency, press to monitor or
change your transmit frequency {page 23}.
• A=B button
Press to copy the data in the currently selected VFO
over to the other VFO {page 30}.
• A/B button
Press to select either VFO A or VFO B {page 13}.
Also, in menu mode, press to select either Menu A
or Menu B {page 16}.
• CLEAR button
Press to reset the RIT/XIT frequency offset to zero
{pages 30, 32}.
• RIT button
Press to switch ON or OFF the Receive Incremental
Tuning function {page 30}.
• XIT button
Press to switch ON or OFF the Transmit
Incremental Tuning function {page 32}.
!8!8
!8!8
!8 SCAN button
Press to start and stop Scan functions {pages 46, 47}.
!9!9
!9!9
!9 M>VFO button
Press to transfer data from a memory channel to a VFO
{page 42}.
@0@0
@0@0
@0 M.IN button
Writes data into a memory channel {page 39} or selects
Memory Scroll mode {page 41}.
@1@1
@1@1
@1 Quick Memory buttons
Controls the Quick Memory function {page 44}.
• M.IN button
Press to write data into Quick Memory {page 44}.
• MR button
Press to recall data from Quick Memory {page 45}.
@2@2
@2@2
@2 FILTER button
Press to select the receive filter bandwidth in SSB, CW,
FSK, or AM mode {pages 36, 38}, or press to select
either narrow-band or wide-band transmit deviation in
FM mode {page 22}.
Note: Selecting the narrow filter bandwidth in SSB mode requires
the optional YK-88SN-1 filter {page 36}.
@3@3
@3@3
@3 CW TUNE button
Press to activate the automatic zero-beat function for
CW mode {page 21}.
@4@4
@4@4
@4 B.C. button
Press to switch ON or OFF the DSP Beat Cancel
function {page 38}.
@5@5
@5@5
@5 N.R. button
Press to toggle between Noise Reduction 1, Noise
Reduction 2, and OFF {page 38}.
PF
ATT PRE-AMP
VOX PROC
SEND
CH1
MIC
CW
FSK
LSB
USB
FM
AM
AT TUNE
POWER
HF TRANSCEIVER TS-570D
PHONES
1
CH2
2
CH3
3
ANT
4
REC
5
FINE
6
NB
7
AGC/TONE
8
REV
9
CLR
F.LOCK
0
ENT
MIC
PWR
KEY
DELAY MENU 1MHz
SPLIT
M/V
DOWN
UP
MR
TF-SET
A=B
SCAN M>VFO M.IN
M.IN
FILTER
CW TUNE
B.C.
N.R.
A/B
CLEAR
RIT
XIT
RIT/XIT
IF SHIFT SQL
CH
46
010
28
AF RF
L
O
W
C
U
T
H
I
G
H
C
U
T
HIGH
DSP SLOPE
LOW
46
010
28
+–
!7 !8
@1
!9 @0
@2 @3@4@5