Filter
Top Products
POWER
CLOCK
CQ-C1110W
D
ISP
SQ
MUTE
789101112SCAN
R
A
N
D
O
M
1
2
3
46
APM
BA
N
D
SRC
5
V
O
L
U
M
E
/
P
U
S
H
S
E
L
REP
TUNE
TRACK
D
•
M
DISP
MUTE
SRC
POWER
CLOCK
CQ-C1110W
D
ISP
SQ
MUTE
789101112SCAN
R
A
N
D
O
M
1
2
3
46
APM
BA
N
D
SRC
5
V
O
L
U
M
E
/
P
U
S
H
S
E
L
REP
TUNE
TRACK
D
•
M
D
ISP
6 7
CQ-C1110W/C1100WCQ-C1110W/C1100W
3
E
N
G
L
I
S
H
4
E
N
G
L
I
S
H
General
Mute
Press [MUTE] to mute the sound completely.
Press [MUTE] again or turn the knob clockwise
to cancel.
Volume
Turn [VOLUME] clockwise to increase
volume, and counterclockwise to
decrease volume.
Volume level (0 to 40)
(default: 18)
Power
Turn the key in the ignition
until the accessory indica-
tor lights.
Power on: Press [SRC]
(POWER).
Power off: Press [SRC]
(POWER) again
and hold.
ACC
ON
MUTE
ST
Display change
Press [DISP] (display) to switch to the clock display.
Note: Please refer to next page when “AdJ” is displayed.
When the power is off:
No display Clock display
Mute indicator
Up
Down
Remote control sensor (➡ page 19)
(only for CQ-C1110W: CQ-C1100W has no remote control function.)
SQ indicator
SQ (Sound Quality)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
Press [SQ] to select a sound type as follows:
SQ -- (default) flat frequency response:
does not emphasize.
SQ - 1 (ROCK) speedy and heavy sound:
exaggerates bass and treble.
SQ - 2 (POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
SQ - 3 (VOCAL) clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Clock setting
Note: If no operation takes place for more than 5 seconds
in audio mode (2 seconds in volume mode), the display
returns to the regular mode.
Audio mode
(Bass/Treble/Balance/Fader)
Volume Bass
Treble
Balance
Fader
Regular mode
Push [SEL] to select the audio mode.
Turn [VOLUME] clockwise to increase volume,
and counterclockwise to decrease volume.
Note: If the fader is set to front, the pre-amp.
output (rear) is decreased.
[DISP] (CLOCK)
The 24-hour system is used for the clock.
[k TUNE], [l TUNE] (Hours, minutes)
Hours
w Press and hold [DISP] (CLOCK) for more than
2 seconds.
Initial time
q Press [DISP] (CLOCK).
(Hours blink.)
e Press [k TUNE] or [l TUNE].
(Hours set.)
Minutes
r Press [DISP] (CLOCK).
(Minutes blink.)
t Press [k TUNE] or [l TUNE].
(Minutes set.)
y Press [DISP] (CLOCK).
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
Time reset
Press and hold [DISP] (CLOCK) for more than
2 seconds to activate the time setting mode to
reset the time.
Then, repeat steps e to y.
(End.)
push
q
w
“AdJ” is displayed when the clock is not adjusted.
Bass:
Adjustable range: –12 dB to +12 dB (by 2 dB step)
Treble:
Adjustable range: –12 dB to +12 dB (by 2 dB step)
Balance:
Adjustable range: 1 to 15 (by 1 step) Balance center
R (right speaker) or L (left speaker)
Fader:
Adjustable range: 1 to 15 (by 1 step) Fader center
F (front speaker) or R (rear speaker)
(default: 0 dB)
(default: 0 dB)
(default)
(default)
(default)
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
•
Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio
signal, readjust bass/treble or volume
(➡ page 7).