Filter
Top Products
User Manual BDL3231/BDL4231
5.1 SETUP MENU
An overall view of the On-Screen Display (OSD) structure is shown below.
You can use it as a reference for further adjusting your monitor.
1. Press DISPLAY MENU button on the remote control.
2. Press cursor UP/DOWN button to choose the item you want to adjust.
3. Press cursor LEFT/RIGHT button to toggle between sub-menu or
adjust the item you selected.
4. Press DISPLAY MENU button on the remote control to return to
sub-menu or press again to exit the menu.
L A N G UA G E
C O MM U N I C AT I O N
C O NF I G U R AT I O N
S E T U P
E N G L IS H
>
>
S M A R TP O R T
S TO R E
R S 2 3 2 I D
S P E E D
D C M T Y P E
C O MM U N I C AT I O N
S P - S PI
>
6 3
1 2 0 0
N O S OU R C E S WI T C H
S M A R TP O R T
S TO R E
R S 2 3 2 I D
S P E E D
D C M T Y P E
C O MM U N I C AT I O N
S P - S PI
>
6 3
1 2 0 0
N O S OU R C E S WI T C H
S M A R TP O R T
S TO R E
R S 2 3 2 I D
S P E E D
D C M T Y P E
C O MM U N I C AT I O N
S P - S PI
>
6 3
1 2 0 0
N O S OU R C E S WI T C H
S M A R TP O R T
S TO R E
R S 2 3 2 I D
S P E E D
D C M T Y P E
C O MM U N I C AT I O N
S P - S PI
>
6 3
1 2 0 0
N O S OU R C E S WI T C H
S M A R TP O R T
S TO R E
R S 2 3 2 I D
S P E E D
D C M T Y P E
C O MM U N I C AT I O N
S P - S PI
>
6 3
1 2 0 0
N O S OU R C E S WI T C H
5.1.1 OSD MENU LANGUAGE
Choose of languages in user interface.
Use cursor LEFT/RIGHT button to toggle between
• ENGLISH • ITALIANO
• FRANCAIS • ESPANOL
• DEUTSCH • 中文
5.1.2 OSD MENU COMMUNICATION
1. Press DISPLAY MENU button on the remote control.
2. Use cursor DOWN button to highlight COMMUNICATION.
3. Use cursor RIGHT button to enter it.
4. Press cursor UP/DOWN button to toggle between
SMARTPORT, STORE, RS232 ID, SPEED or DCM TYPE.
5. Press DISPLAY MENU button on the remote control to return to
sub-menu or press again to exit the menu.
SMARTPORT
Use cursor LEFT/RIGHT button to toggle between OFF, SP-SPI, and
SP-I2C. For normal stand-alone applications select OFF under the
SMARTPORT.
RETURN TO THE CONTENT
S
5. OSD MENU
Important note:
The COMMUNICATION menu shows items that are relevant for system integrators that develop their own cards (also
called Smart Cards or Data Communication Modules, DCM’s) and for the use of Philips branded Smart Cards. These items can
be relevant in case a Philips or third party Smart Card is used that requires a certain setup. The card slot of the set has
several by the industry accepted serial interfaces (SP-SPI and SP-I2C) of which only one will be used at the same time.
Please consult the User Manual of the applicable card for the correct COMMUNICATION setup.
The RS232 function is independently available of SP-SPI and SP-I2C and is always switched "ON".
The communication SPEED (baud rate) can be adjusted to the required baud rate of the external control system.