Filter
Top Products
FAD/BAL(fader/balanceadjustment)
1 PressM.C. todisplay the settingmode.
2 PressM.C. tocycle between faderand balance.
3 Turn M.C.to adjustthe speakerbalance.
Adjustment range(front/rear): F-F15 toF-R15
Adjustment range(left/right): B-L15 toB-R15
! F-0 isthe propersetting whenonly two speak-
ers areused.
! When therear outputand RCAoutputsetting
are SUBW, youcannot adjustfron t/rear speak-
er balance.Refer toSW control(rear output
and subwoofersetting) on thenext page.
Preset EQ(equalizer recall)
1 PressM.C. todisplay the settingmode.
2 Turn M.C.to selectan equalizercurve.
Powerful—Natural—Vocal—Custom1—Cus-
tom2—Flat—S.Bass
! When Flatis selectedno adjustments are
made tothe sound.
3 PressM.C. toconfirm the selection.
Graphic EQ(equalizer adjustment)
You canadjust thecurrently selected equalizercurve
setting asdesired. Adjustedequalizercurvesettings
are memorizedin Custom1or Custom2.
! A separateCustom1 curve canbe created for
each source.If youmake adjustments whena
curveother thanCustom2 is selected,the equali-
zer curve settingswill bememorized inCustom1.
! A Custom2curvecan be createdcommon toall
sources. Ifyou make adjustmentswhen theCus-
tom2 curve isselected, theCustom2 curve will
be updated.
1 PressM.C. todisplay the settingmode.
2 PressM.C. tocycle between equalizerband and
level.
3 PressM.C. toswitch toequalizerband andthen
turn M.C.to select.
100Hz—315Hz—1.25kHz—3.15kHz—8kHz
4 PressM.C. toswitch tolevel and thenturn M.C.
to adjust.
Adjustment range:+6 to–6
Loudness (loudness)
Loudness compensatesfor deficiencies inthe low-
and high-frequencyranges atlow volume.
1 PressM.C. todisplay the settingmode.
2 Turn M.C.to selectthe desiredsetting.
OFF (off)—Low(low)—Mid (mid)—High (high)
3 PressM.C. toconfirm the selection.
SW setting1 (subwooferon/off setting)
This unitis equippedwith asubwooferoutput which
can beturned onor off.
1 PressM.C. todisplay the settingmode.
2 Turn M.C.to selectthe desiredsetting.
Normal (normalphase)—Reverse (reverse
phase)—OFF (subwooferoff)
3 PressM.C. toconfirm the selection.
SW setting2 (subwooferadjus tment)
When thesubwoofer outputis on,you can adjustthe
cut-off frequencyand the outputlevel ofthe subwoo-
fer.
Only frequencieslower than thosein theselected
range areoutputted fromthe subwoofer.
1 PressM.C. todisplay the settingmode.
2 PressM.C. tocycle between cut-offfrequency and
output levelof subwoofer.
3 PressM.C. toswitch tocut-offfrequencyand then
turn M.C.to selectcut-off frequency.
50Hz—63Hz—80Hz—100Hz—125Hz
4 PressM.C. toswitch tooutput level andthen turn
M.C. toadjust outputlevel.
Adjustment range:+6 to-24
HPF setting(high passfilter adjustment)
When youdo notwant lowsounds from thesubwoo-
fer outputfrequency rangeto play fromthe frontor
rear speakers,turn onthe HPF (highpass filter).Only
frequencies higherthan thosein the selectedrange
are outputfrom thefront orrear speakers.
1 PressM.C. todisplay the settingmode.
2 Turn M.C.to selectcut-off frequency.
OFF (off)—50Hz—63Hz—80Hz—100Hz—125Hz
3 PressM.C. toconfirm the selection.
Bass booster(bass boost)
1 PressM.C. todisplay the settingmode.
2 Turn M.C.to adjustthe level.
Adjustment range:0 to+6
3 PressM.C. toconfirm the selection.
En
15
English
Section
02
Operating this unit