RCA DRC62708 Car Video System User Manual


  Open as PDF
of 12
 
16
17
Tv Display
Pan Scan
• Whenwide-screenvideoisplayed,thismodeclipstherightandleftsides
of the image so that it can be viewed on a conventional screen.
•Somewide-screenDVDsthatdonotpermitPanScanmodeplaybackare
automatically played in letterbox mode (black bands that appear at the
top and bottom of the screen).
Letter Box
• Whenwide-screenvideoisplayedinthismodeonaconventionalscreen,
black bands appear at the top and bottom of the screen.
Wide screen
• Thisisthecorrectmodeforplayingwide-screenvideosontheunitorother
external wide-screens.
Note:
•ThedisplayablepicturesizeispresetontheDVD.Thereforetheplayback
picture of some DVDs may not conform to the picture size selected.
•WhenyouplayDVDsrecordedinthe4:3aspectratio,theplaybackpicture
will always appear in the 4:3 aspect ratio regardless of the TV display
setting.
•SelectWideScreentoconformtheLCDscreenontheunit.Alwaysbesure
that your TV display conforms to the actual TV in use if you connect the
unit to a TV.
Default
It takes 3-5 seconds to reset the unit to the factory default.
Cut off when a wide-screen
video image is played
Pan Scan
Letter Box
Wide Screen
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• DoNOTtouchthesurfaceoftheunlabeledsideofthedisc.
• DoNOTstickpaperortapeonthesurface.
• DoNOTexposethedisctodirectsunlightorexcessiveheat.
•Cleanthediscbeforeplayback.Wipethediscfromthecenteroutwardwithacleaning
cloth.
• NEVERusesolventssuchasbenzineoralcoholtocleanthedisc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause
malfunctions.
Cleaning the Unit
• Besuretoturntheunitoffanddisconnectthepowersourcebeforemaintainingtheunit.
• Wipetheunitwithadrysoftcloth.Ifthesurfacesareextremelydirty,wipecleanwithacloththathas
been dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe with a dry cloth.
• Neverusealcohol, benzine,thinner,cleaning uidor otherchemicals.DoNOTusecompressed airto
remove dust.
Important Note
• Beforetransportingtheunit,removeanydiscfromthedisccompartment.
Maintenance
Customizing the Function Settings
Language Setup
1. Press the SETUP button.
2. Press the button to select Language setup page.
3. Use the or button to select the option (OSD
Language, Audio, Subtitle or Disc Menu), then press the
button.
4. Use the or button to select your preferred language,
then press the ENTER button to confirm.
5. Press the button to go back to the previous menu.
Repeat steps 2 and 3 to adjust other options.
6. Press the SETUP or RETURN button to exit the menu.
Note:
• SomeDVDsmaynotplayintheaudiolanguageselected.Apriorlanguagemaybeprogrammedonthe
disc.
• SomeDVDsmaybesettodisplaysubtitlesinalanguageotherthantheoneselected.Apriorsubtitle
language may be programmed on the disc.
• SomeDVDsallowyoutochangesubtitleselectionsviathediscmenuonly.Ifthisisthecase,pressthe
MENU button and choose the appropriate subtitle from the selection on the disc menu.
• SomeDVDs maynot includedyourpre-selected language.In thiscase,the DVDplayerautomatically
displays disc menus consistent with the disc’s initial language setting.
Video Setup
1. Press the SETUP button in stop mode.
2. Press the or button to select Video Setup Page.
3. Press the or button to select the option (Brightness
or Contrast), then press the button.
4. Press the or button to adjust the setting, then press
the ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
System Setup
1. Press the SETUP button in stop mode.
2. Press the or button to select System Page.
3. Press the or button to select the option (TV Display
or Default), then press the button.
4. Press the or button to adjust the settings, then press
the ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
 previous