Gasoline Engine Safety
The engine exhaust from this sprayer contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.
1
. Honda engines are designed to give safe and dependable
service if operated according to instructions. Read and
understand the Honda Owner's Manual before operating
the engine. Failure to do so could result in personal injury
or equipment damage.
2. To prevent fire hazards and to provide adequate
v
entilation, keep the engine at least 1 meter (3 feet) away
from buildings and other equipment during operation. Do
not place flammable objects close to the engine.
3. Children and pets must be kept away from the area of
operation due to a possibility of burns from hot engine
components or injury from any equipment the engine may
be used to operate.
4. Know how to stop the engine quickly, and understand the
operation of all controls. Never permit anyone to operate
the engine without proper instructions.
5. Gasoline is extremely flammable and is explosive under
certain conditions.
6. Refuel in a well-ventilated area with the engine stopped.
Do not smoke or allow flames or sparks in the refueling
area or where gasoline is stored.
7. Do not overfill the fuel tank. After refueling, make sure
the tank cap is closed properly and securely.
8. Be careful not to spill fuel when refueling. Fuel vapor or
spilled fuel may ignite. If any fuel is spilled, make sure
the area is dry before starting the engine.
9. Never run the engine in an enclosed or confined area.
Exhaust contains poisonous carbon monoxide gas;
exposure may cause loss of consciousness and may lead
to death.
10. The muffler becomes very hot during operation and
remains hot for a while after stopping the engine. Be
careful not to touch the muffler while it is hot. To avoid
severe burns or fire hazards, let the engine cool before
transporting it or storing it indoors.
11. Never ship/transport sprayer with gasoline in the tank.
DO NOT use this equipment to spray water or acid.
Do not lift by cart handle when loading or unloading.
4 © Titan Tool Inc. All rights reserved.
Specifications
Gas Sprayer
Gallons per minute (GPM)...............2.15 (8.14 LPM)
Cycle rate per gallon........................51 (14.5 cycles/liter)
Maximum tip sizes ...........................1 gun = .048”
2 guns = .033”
3
guns = .023”
4 guns = .019”
Maximum pressure ..........................3300 PSI (22.8 MPa)
Power...............................................Honda 5.5 HP, 4-stroke,
single cylinder, overhead
v
alve engine w/oil alert
Fuel capacity....................................0.97 US gallons
(approx. 3.5 hours run time)
Halogenated solvent compatible......Yes
Weight..............................................149 lbs. (67.6 kg.)
Inlet paint filter .................................10 mesh “Rock Catcher”
Outlet paint filter...............................50 mesh, 18 in.
2
Pump inlet........................................1” NPT(F)
Pump outlet......................................1/2” NPT(F) to paint filter
Paint filter hose connections............3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions ......................................43" L (109 cm) x
26" W (66 cm) x
35" H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teflon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
Electric Sprayer
Gallons per minute (GPM)...............1.25 (4.7 LPM)
Cycle rate per gallon........................55 (14.5 cycles/liter)
Maximum tip sizes ...........................1 gun = .036”
2 guns = .026”
3 guns = .019”
Maximum pressure ..........................3300 psi (22.8 MPa)
Power...............................................2 HP DC Motor,
115V 15.5A,
overload protected
Halogenated solvent compatible......Yes
W
eight..............................................
165 lbs. (74.8 kg.)
Inlet paint filter .................................10 mesh “Rock Catcher”
Outlet paint filter...............................50 mesh, 18 in.
2
Pump inlet
........................................
1” NPT(F)
Pump outlet......................................1/2” NPT(F) to paint filter
Paint filter hose connections............3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions ......................................43" L (109 cm) x
26" W (66 cm) x
35" H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teflon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
