Filter
Top Products
13-EN
Adjusting Subwoofer Level/Bass Level/
Middle Level/Treble Level/Balance (Between
Left and Right)/Fader (Between Front and
Rear)/Loudness/Defeat
1
Press AUDIOSETUP repeatedly to choose the desired
mode.
Each press changes the mode as follows:
SUBWOOFER
*1
BASS LEVEL
*2
MID LEVEL
*2
TRE LEVEL
*2
BALANCE FADER LOUDNESS
*2/*3
DEFEAT VOLUME
SUBWOOFER
*1 When the subwoofer mode is set to OFF, its level cannot be
adjusted.
*2 Adjustable only when DEFEAT is OFF.
*3 For details about loudness, refer to “Turning Loudness On/Off”
on page 13.
Note
• If no operation is performed for 5 seconds, the unit automatically
returns to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
MID, TRE LEVEL and LOUDNESS will return to the factory
defaults.
Audio Setup
You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
1
Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select AUDIO, and then press
ENTER.
AUDIO GENERAL DISPLAY iPod BLUETOOTH
3
Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
(e.g. Select SUBWOOFER)
FACTORY EQ
*1/*2
LOUDNESS
*1
3BAND EQ
*1/*3
VOL LV ADJ
HPF
*1
SUBWOOFER SUBW LPF
*1/*4
SUBW PHASE
*4
SUBW SYS
*4
POWER IC
*1 Adjustment cannot be performed when DEFEAT is set to ON.
*2 The FACTORY EQ’s setting value and 3BAND EQ’s setting
value are linkage.
*3 The FACTORY EQ’s setting value and 3BAND EQ’s setting
value are linkage. In step 3, three sound adjustment items (Bass,
Mid and Treble) can be selected in 3BAND EQ mode, turn the
Rotary encoder to select the desired item, and then press
ENTER to continue to step 4.
*4 These functions are inoperable when Subwoofer is set to OFF.
4
Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select SUBW ON or SUBW OFF)
5
Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
•Pressing returns to the previous Sound menu mode.
• Pressing and holding for at least 2 seconds will return to normal
mode.
• If no operation is performed for 60 seconds, Sound menu mode is
canceled.
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Setting item: FACTORY EQ
Setting contents:
USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /
ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL
Loudness introduces a special low-and high-frequency emphasis at low
listening levels. This compensates for the ear’s decreased sensitivity to
bass and treble sound.
Setting item: LOUDNESS
Setting contents:
OFF (Initial setting) / ON
Sound Setting
Subwoofer +0 ~ +15
Bass level -7 ~ +7
Middle level -7 ~ +7
Treble level -7 ~ +7
Balance L15 ~ R15
Fader R15 ~ F15
Loudness ON/OFF
Defeat ON/OFF
Volume 0 ~ 35
AUDIO/SETUP
Rotary encoder
/ENTER
Use steps 1 to 5 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
Equalizer Presets (F-EQ)
Turning Loudness On/Off