Alpine CDE-123 Car Stereo System User Manual


 
23-EN
* The illustration is for CDE-123.
Connecting the Flash Memory (optional)
If a Flash Memory device/Portable audio player is connected to the unit,
MP3/WMA/AAC files can be played back.
Note
When TAG is set in “Setting the USB Search Mode” (refer to “Setting the
USB Search Mode” on page 22), in the USB mode, when this unit is
reset, ACC is switched from OFF to ON, or when the USB is connected
to this unit, “BANKING” is displayed for several seconds.
There are two USB connectors on CDE-123, you can choose to connect
an Flash Memory to Front USB Connection Terminal or Rear USB
Connector. There is only one USB connector (Front USB Terminal) on
CDE-124SXM/CDE-122.
1
Open the cover of the USB Connection Terminal.
2
Connect the Flash Memory directly to the USB Connection
Terminal, or via the USB cable.
1
Carefully, pull out the Flash Memory from the USB cable or
the USB Connection Terminal.
2
Close the cover of the USB Connection Terminal.
Notes
Change to a source other than the Flash Memory mode, then remove
the Flash Memory. If the Flash Memory is removed in the Flash
Memory mode, data may be damaged.
When removing Flash Memory, pull it out straight.
If sound is not output or Flash Memory is not recognized even when
Flash Memory is connected, remove Flash Memory once, and then
connection it again.
Route the USB cable away from another cables, etc.
After removing the Flash Memory, close the cover of the USB
Connection Terminal to prevent dust or foreign objects from entering
and causing a malfunction.
On how to connect an Flash Memory to Rear USB Connector, refer to
“Rear Flash Memory Connection (CDE-123 only) (sold separately)” on
page41.
Using the Flash Memory/Portable audio
player Banking Function
Note
When a Flash Memory is connected, the following description is
available only when TAG is set in “Setting the USB Search Mode” (refer
to “Setting the USB Search Mode” on page 22).
What is a Bank?
A bank is a unit of up to 1,000 songs, which is stored in memory.
“BANKING” refers to the grouping of songs available in Flash Memory, in
banks of 1,000 songs each. However, when a Flash Memory is
connected, 1BANK can store up to 1,000 songs under the following
conditions. Otherwise, the number of songs that can be stored may be
less than 1,000.
Conditions (general estimate values)
Playlists: 20 (32 characters; 64 bytes)
Genres: 10 (32 characters; 64 bytes)
Composers: 30 (32 characters; 64 bytes)
Artists: 30 (32 characters; 64 bytes)
Albums: 100 (32 characters; 64 bytes)
Titles: 1,000 (32 characters; 64 bytes)
Folders: 100 (32 characters; 64 bytes)
Files: 1,000 (32 characters; 64 bytes)
File Paths: 1,000 (128 characters; 256 bytes)
About Banking
While a bank is being built up, “BANKING” is displayed. Banking occurs
whenever a Flash Memory device/Portable audio player is connected or
after power to the head unit turns on.
It can take anywhere from a few seconds to up to several minutes for
banking to complete. This depends on the number of files and folders
in Flash Memory/Portable audio player.
Available operations while Banking
During Banking, the information display changes so the VIEW
operation is not available.
With a song playing, Regular fast-forwarding and next song selection is
available.
While Banking, the song playback order may differ from the song order
in the Flash Memory device/Portable audio player.
Searching is not recommended during the Banking process as the
database is under construction at this time, and malfunction may result
in some cases.
Flash Memory/Portable
audio player (optional)
When connect Flash Memory to Front USB
Connection Terminal
Rotary encoder/ /ENTER
SOURCE/
VIEW
BAND/ F/R
Preset buttons
(1 through 6)
USB Connection Terminal
This unit
Flash Memory
(sold separately)
or
Flash Memory
(sold separately)
Cable (sold
separately)
Remove Flash Memory from Front USB
Connection Terminal