Filter
Top Products
D·
•
Speakers
/
Haut-parleurs
/
Bocinas
,·(·G;e;n)t~;rt)t(v;rde)-
------------------------------,,
(!)~
RearlefV
.
1 :
Gauchearn!re
/
I
(Green/Biack)/(verl/nolr)/(Verde/negro)
I e
Posterior
Izqu
i
erdo
I I
1
(Whlte)/(blanc)/(Bianco)
1
(!)~
Front
lefV
~--~~~~~~~~;;,;;=:::;:;;::::;=============,1
GaucheavanV
(Whlle/Biack)/(blanc/nolr)/(Bianco/negro)
: e
Frontal
Izquierdo
(Grey)/(grls)/(Grls)
:
~
~
r
~:/ena~~~V
(Grey/Biack)/(gris/nolr)/(Grls/negro)
:
8'-J
Frontal
derecha
(VIolel)/(vlolei)/(VIolela)
1
(!)~
Rear
righV
~--~~~~~~~~~~::;:=;;;;::;::;=============::
Droitearri!re
/
,
(VIoleVBiack)
(vlolel/nolr)/(VIolela/negro)
, e
Posterior
derecha
'R"E'MiiiE
riiR"N:o"NiAcr~v~iloN-o~
~
r~~EcoririA;o-EiE;r:E;O",iio-
REMiiro- -ii-
(Biue/While)/(bleu/blanc)/(Azul/blanco)
GNO/TERRE/Tierra
(Biack)/(nolr)/(Negro)
BATTERY/BATTERIE!BATERiA
(Yellow)/(jaune)/(Amarollo)
•
KTP-445U
Left
end
panei/Le
panneau
de
gauche/panel
de
Ia
izquierda
Fig. 3
u w
REMOTE
TURN-ON/ACTIVATION
DE
LA
TELECOMMANDE/ENCENDIDO
REMOlD
•
(Biue/While)/(bleu!blanc)/(Azul!blanco)
KTP-445U
Right
end
panel/panneau
de
droite/panel
de
Ia
derecha
Fig.4
FRONT
IN
/
:~~~~EI
ENTRADA
FRONTAL
REA~N
/
ARRI
RE
ENTRE/
ENTRADA
POSTERIOR
CONNECTIONS (Fig. 3 and Fig. 4)
Before making connections, be sure
to
turn the power off to all
audio components. Connect the yellow battery lead from the
amp directly to the positive(+) terminal of the vehicle's battery.
Do
not connect this lead to the fuse block.
&cAUTION
+ Caution on connection terminals/parts
• Keep electrically conductive objects away from the unit's
terminals/parts (power terminals, fuses, speaker output
terminals,
RCA connectors, etc.). Doing so prevents a
possible short circuit and damage to the unit.
To
prevent
external
noise
from
entering
the
audio
system.
Locate the unit and route the leads at least
10
em
(3-
15
/16') away from the car harness.
Keep the battery power leads as far away from other leads
as possible.
Connect the ground lead securely to a bare metal spot
(remove any paint or grease if necessary) of the car
chassis.
Your Alpine dealer knows best about noise prevention
measures so consult your dealer for further information.
0
Output/Power
Connector
•
Input
Connector
• Fuse (15A X 1)
USE ONLY THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do so may result
in
fire or electric shock.
8
Output/Power
Wire
Harness
• Speaker
Output
Wires
Referring to "Cautions on speaker wire connections·;
connect each speaker output wire to the correct
corresponding speaker wire
on
the vehicle side.
Note:
Do not connect speaker leads together or
to
chassis ground.
•
Battery
Lead (Yellow)
There are two options:
a.
Connect battery lead to OEM radio fused circuit
The
OEM radio circuit has a fuse to protect your
vehicle's electrical system
in
case of a short circuit. Do
not connect the battery lead to the
OEM radio circuit if
the fuse rating
is
less than 15A.
b.
Connect battery lead directly to
BATT+
Be sure to add a 15A fuse (sold separately) as close as
possible to the battery's (
+)
terminal.
8 Remote
Out
Lead {Blue/White)
Use this lead to turn
on
additional amplifiers.
Note:
This is a pass through Remote Turn-On signal from the head
unit.
0
Ground
Lead
(Black)
Connect this lead securely to a clean, bare metal spot
on
the vehicle's chassis. Verify this point to be a true ground
by checking for continuity between that point and the
negative(-) terminal of the vehicle's battery. Ground
all
your audio components to the same point
on
the chassis to
prevent ground loops.
•
Input
Wire
Harness
4t
Input
Signal
Wires
There are two options:
a.
RCA Input Jacks (FRONT =Violet sleeve, REAR=Grey
sleeve)
Connect these jacks to the line out leads on your head
unit using
RCA extension cables (sold separately).
b.
Speaker Level Inputs
Note:
Cut off the RCA jacks, then connect the correct
corresponding speaker outputs from the head unit
directly to these twisted pair wires.
For the
"Speaker Level Input System" setting. connecting the
Remote Turn-On Lead is not required due to the
"REMOTE
SENSING"
function
of
this product. However, the "REMOTE
SENSING"
function may no/ work depending
on
the signal
source connected. In such a case, connect the Remote
Turn-On
Lead
to
an incoming power supply wire (accessory power)
in
the
ACC
position.
8 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on or power antenna
(positive trigger, (+)
12V only) lead of your head unit.
Note:
• See connection check list in Fig.
7.
for
more details.