Filter
Top Products
37-EN
01GB05VPAB222R.fm
ALPINE VPA-B222R 68-02065Z87-A (EN)
7
Repeat step 5 and 6 to set each speaker.
• If the centre speaker is turned “OFF,” the centre channel’s audio
signals are added to the audio signals output from the front speakers.
• If you set the speaker response to “OFF,” also set the speaker setting
to “OFF” (page 32).
• Perform the setup for all the speakers (“Front,” “Centre,” “Rear”
and “Subwoofer”). Otherwise, the sound may not be balanced.
• When the centre speaker is set to “OFF”, the setting is ineffective
even if centre is set with this function.
• Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
• When using PRO LOGIC II, if the rear speaker is set to “LARGE”,
there will be no output from the subwoofer.
Setting of Dolby Digital
1
Check that Defeat mode is off (page 12).
2
Press and hold TA/RTN/SETUP for at least 2
seconds.
The SETUP screen is displayed.
3
Press the joystick up or down to select AP SETUP,
then press the joystick right.
The AP SETUP screen is displayed.
4
Press the joystick up or down to select MULTI CH
SET, then press the joystick right.
The MULTI CH SET screen is displayed.
5
Press the joystick up or down to select the desired
item.
Set the items below as you desire.
In most installations, the centre speaker must be placed directly between
the front passenger and driver. Using this function, the centre channel
information is distributed to the left and right speakers. This creates an
acoustic image simulating a centre speaker directly in front of each
listener. Adjusting the centre width in PL II MUSIC (see “Using the Pro
Logic II Mode,” page 39), makes this function ineffective.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if the Decode mode is switched.
1 Press the joystick left or right to select ON of BI-
PHANTOM.
2 Press the joystick down to select BI-PHANTOM LV.
3 Press the joystick left or right to adjust the level.
The level can be adjusted within the range of -5 to +5. The
higher the level, the more the position of the centre speaker is
shifted to the sides.
The BI-PHANTOM function is turned off when setting to
OFF.
• This adjustment is effective when the setting of the centre speaker to
SMALL or LARGE in the speaker setup settings.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 32).
This function mixes the front channel audio signals to the audio signals
output from the rear speakers, improving the sound in the vehicle’s rear
seat.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if the Decode mode is switched.
1 Press the joystick left or right to select ON of REAR MIX.
2 Press the joystick down to select MIX LEVEL.
3 Press the joystick left or right to adjust the level.
The level can adjusted in five steps: -6, -3, 0, +3 and +6. The
higher the level, the more bass is output from the rear speakers.
(The effect differs depending on the software (DVD, etc.)).
The REAR MIX function is turned off when set to OFF.
• This adjustment is ineffective when the rear speaker setup setting is
set to “OFF”.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
Adjusting the acoustic image
Mixing bass sound to the rear channel
01GB00VPAB222R.book Page 37 Monday, January 23, 2006 4:24 AM