Filter
Top Products
8
10 CSB Corner Subwoofer
Example 6: Speaker Out/High Level In for 1 Subwoofer
This is the most common method for connecting a subwoofer to a system without a dedicated subwoofer line
out or preamp outputs. The signal that comes from the High-Level Output jacks is hi-pass filtered to prevent
overdriving the satellites with deep bass frequencies.
RIGHT
+
-
L/MONO
-
+
OUTPUT
HIGH
LEVEL
INPUT
STDBY
RIGHT
L/MONO
LOW
LEVEL
LOWPASS
BYPASS
AUTOOFF ON
NORMAL
1800
FREQ
PHASE
LEVEL
16050
MAXMIN
STATUS
220-240V
RISK OF ELECTRIC SHOCK
DO NOT OPEN
110-120V
POWER
CAUTION
WARNING
ON OFF
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLICANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
FUSE 115,T2AL/250V
FUST 230V,T1.25AL/250V
110-120VAC~60Hz
220-240VAC~50Hz
180WATTS
Subwoofer
Receiver/Processor
Example 7: Speaker Out/High Level In for Stereo Subwoofers
This is the most common method for connecting 2 subwoofers to a system without a dedi-
cated subwoofer line out or Preamp outputs. Note that the L/MONO High Level input is
used on both left and right subwoofers.
RIGHT
+
-
L/MONO
-
+
OUTPUT
HIGH
LEVEL
INPUT
STDBY
RIGHT
L/MONO
LOW
LEVEL
LOWPASS
BYPASS
AUTOOFF ON
NORMAL
1800
FREQ
PHASE
LEVEL
16050
MAXMIN
STATUS
220-240V
RISK OF ELECTRIC SHOCK
DO NOT OPEN
110-120V
POWER
CAUTION
WARNING
ON OFF
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLICANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
FUSE 115,T2AL/250V
FUST 230V,T1.25AL/250V
110-120VAC~60Hz
220-240VAC~50Hz
180WATTS
Right Subwoofer Receiver/Processor
RIGHT
+
-
L/MONO
-
+
OUTPUT
HIGH
LEVEL
INPUT
STDBY
RIGHT
L/MONO
LOW
LEVEL
LOWPASS
BYPASS
AUTOOFF ON
NORMAL
1800
FREQ
PHASE
LEVEL
16050
MAXMIN
STATUS
220-240V
RISK OF ELECTRIC SHOCK
DO NOT OPEN
110-120V
POWER
CAUTION
WARNING
ON OFF
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLICANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS:RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
FUSE 115,T2AL/250V
FUST 230V,T1.25AL/250V
110-120VAC~60Hz
220-240VAC~50Hz
180WATTS
Left
Speaker
Right
Speaker
Left
Speaker
Right
Speaker
Left Subwoofer
You can connect to the High-level inputs by removing 1/2" of insulation from each wire end,
twisting the strands of wire together and placing the wire into the appropriate terminal's
hole on the rear of the subwoofer while pushing the adjacent latch as illustrated. Be careful
that no stray strands of wire touch across connections.
It is important to observe polarity while making speaker connections: red (+) terminals
on the amplifier to red (+) on the speaker, black (–) on the amplifier to black (–) on the
speaker. Look carefully at the wires you are using and note that one of the wires in each
pair will be marked by either the conductor color, printing on the wire jacket, a ridge on
one side of the wire jacket, or a thread intertwined with the wire strands. By convention,
the marked wire is connected to the red (+) terminal.
Connections