Filter
Top Products
60 VRX925VD
English
Owner’s manual
Multiple Channel Processor Operations
Selecting t.he DSF mode or the
P.EQ mode
1. Press the [A-M] button.
2. Touch the [STATUS] key to select “DSF” or
“P.EQ”.
3. Touch the [DSF] or [P.EQ] to select a desired
mode and to set the mode thus selected.
4.
After setting, touch the [RNT] key or press the
[A-M] button to return to the previous mode.
DSF mode
DSF effect ON/OFF
∗ The factory default setting is “OFF”.
1. Press the [A-M] button.
2. Touch the [DSF] key to select “on” and “off”.
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD screen.
Note:
•
If the DSF effect is set to OFF, the adjustment
made in “DSF” is not reflected in the music source.
Selecting the DSF type
1.
Press the [A-M] button and touch the [DSF] key.
2. Touch the key for the desirable type to select it.
3. When the setting is finished, touch the [RTN]
key or press the [A-M] button to return to the
previous mode.
P.EQ mode
P.EQ effect ON/OFF
∗ The factory default setting is “OFF”.
1. Press the [A-M] button.
2. Touch the [P.EQ] key to select “on” and “off”.
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD screen.
Note:
• If the P.EQ effect is set to OFF, the adjustment
made in “P.EQ” is not reflected in the music
source.
Setting and storing P.EQ Properties
1. Press the [A-M] button to show the AUDIO
MODE menu.
2. Touch the [P.EQ] key to show the P.EQ
adjusting display.
3.
Touch the key for the desirable type to select it.
The P.EQ adjustment contents are as
follows:
●SIGNAL
∗ The factory default setting is “P.NOISE”.
This function selects [P. NOISE] or [MUSIC].
●SPEAKER SELECT
∗ The factory default setting is “FRONT”.
This function selects [FRONT], [CENTER] or
[SURROUND].
●“BAND”
∗ The factory default setting is “BAND1”.
Select the channel to be compensated
(BAND1, BAND2, BAND3).
●“FREQUENCY”
∗ The factory default setting is “1 kHz”.
Select the center frequency that you want to
compensate from the range of 20 Hz to 20
kHz. (1/3 octave step, 31 points)
●“Q”
∗ The factory default setting is “1”.
Set the sharpness of the Q-curve to one of
the parameters: 1, 3, 5, 7 and 20.
●“GAIN”
∗ The factory default setting is “0”.
Adjust the gain (output level) in the range of -
12 dB to +12 dB. (1 dB step, 25 points)
4. After making adjustments to a desired
pattern by repeating the operations of item3,
touch the [RNT] key or press the [A-M]
button to return to the previous mode.
Selecting the Dolby PL
II
(Dolby Pro
Logic
II
) type
1. Press the [A-M] button and touch the [Dolby
PLII] key.
2.
Touch the key for the desirable type to select
it.
3. When the setting is finished, touch the [RTN]
key or press the [A-M] button to return to the
previous mode.
∗ The factory default is “off”.