Filter
Top Products
98
access the 32k+ variable colour setting mode. See Page 10
for more information
11. BAND/SEARCH
a) In Tuner mode, press this button to cycle through Bands:
FM1, FM2, FM3, AM1 (MW1) or AM2 (MW2).
b) In Media playback mode, press to access the folder / file
search mode.
c) In iPod/iPhone playback mode, press this button to
access the iPod/iPhone search functions.
12. MENU
Press to access the system menu. See Page 9 for menu
options.
13. TUNE UP/DOWN, FILE & TRACK UP/DOWN & FAST
FORWARD/BACK
a) TUNE UP/DOWN. In tuner mode, press this button to
Auto Seek to the next station or press and hold this button
to manually tune in to your desired station.
b) FILE & TRACK UP/DOWN. In CD or USB/SD media
playback mode, press these buttons to skip a chapter,
track or file.
c) FAST FORWARD/BACK. In USB/SD media playback
mode, press and hold momentarily to fast forward/rewind.
14. SOURCE BUTTON
Press the Source Button to cycle through the following
sources if available: Radio: CD: USB: SD: AUX
AUDIO FUNCTIONS
All Audio functions are easily accessable on the CA-ML600.
AUDIO MENU. Press the ENCODER VOLUME CONTROL
to access the Audio Menu mode. Then press ENTER or
TUNE UP to select the Audio Function to be adjusted,
then rotate the ENCODER VOLUME CONTROL to select
the desired setting. You can always return to the previous
Audio Function by pressing the TUNE DOWN button.
REMINDER
In the AUDIO MENU, or in any menu, you can quickly exit the menu
by pressing the ESC/RGB button
EBX ON/OFF: Turn ON or OFF the EBX (Encounter Bass
Xtender) Bass Boost.
BAS Adjust the Bass level between -7 to +7.
TRE Adjust the Treble level between -7 to +7.
BAL (Balance) Adjust the balance between the right and left
speakers from 12R (full right) to 12L (full left).
FAD (Fader) Adjust the fader between the front and rear
speakers from 12R (full rear) to 12L (full front).
(SUBWOOFER)
SW ON/OFF Turn On or Off the Subwoofer RCA output.
SW LPF Subwoofer low pass crossover: 80/120/160Hz
SWAM ON/OFF In AM mode, turn ON or OFF the Sub output.
NOTE
If the Subwoofer RCA output is set to “OFF”, then the SW LPF &
SWAM functions will not be displayed.
EQUALISER OPERATION
When you activate the Equaliser, the Pre-Set Equaliser settings
override your existing Bass, Midrange & Treble Settings.
Press the Equaliser button repeatedly to cycle through
the following pre-sets: FLAT->POP->USER->DANCE-
>ROCK->CLASSIC->JAZZ->VOCAL
To return to the Bass & Treble settings that were in use before
the EQ was selected, please select the USER setting.
SYSTEM MENU
Press (MENU) to access the System Menu and press
again to select the item be adjusted, then rotate Encoder
Volume Knob to select a value / option. To exit this menu at
any time, press the ESC/RGB button
STORE (Auto store)
While in Tuner mode, press the ENCODER VOLUME CONTROL
to activate Auto Store. The six strongest stations of the selected
band will be saved in the preset channels automatically
RDS ON/OFF
While in Tuner mode, this selection turns On or Off RDS.
RDS Functions are explained in more detail on Page 8. If
RDS is set to OFF, then the RDS Functions indicated below
with an * will not appear in the System Menu
PTY* (Program Type)
Press the ENCODER VOLUME CONTROL to enter program
type, then rotate the ENCODER VOLUME CONTROL to
select the category.
AF* ON/OFF
Turn On or Off the Alternate Frequencies function.
TA* ON/OFF
Turn On or Off the Traffic Announcement function.
REG* ON/OFF
Turn On or Off the Set Region for Alternate Frequencies function
CT* ON/OFF
Turn On or Off the CT function.
LOC* ON/OFF
(Local/Distance). Use this setting to Auto Seek to strong
local stations (Local) or all stations regardless of their
strength (Distance).
AREA
Select your country/region for the tuner:
OCEANIA (Australia/New Zealand); USA; EUROPE;
RUSSIA & press ESC/RGB to save.
CLK (Clock)
To set the clock, rotate the Encoder Volume Control to set
the hours (Note “A” or “P” will be displayed in the top-right
hand of the LCD display indicating AM or PM if the Clock
is in 12H mode – see below). Press the Encloder Volume
control to select “minutes” then rotate the control to set.
CLK 12H/24H (Clock Format)
Select the time format 12H or 24H
BEEP ON/OFF
Select On or Off to activate button confirmation beep tones.
98
access the 32k+ variable colour setting mode. See Page 10
for more information
11. BAND/SEARCH
a) In Tuner mode, press this button to cycle through Bands:
FM1, FM2, FM3, AM1 (MW1) or AM2 (MW2).
b) In Media playback mode, press to access the folder / file
search mode.
c) In iPod/iPhone playback mode, press this button to
access the iPod/iPhone search functions.
12. MENU
Press to access the system menu. See Page 9 for menu
options.
13. TUNE UP/DOWN, FILE & TRACK UP/DOWN & FAST
FORWARD/BACK
a) TUNE UP/DOWN. In tuner mode, press this button to
Auto Seek to the next station or press and hold this button
to manually tune in to your desired station.
b) FILE & TRACK UP/DOWN. In CD or USB/SD media
playback mode, press these buttons to skip a chapter,
track or file.
c) FAST FORWARD/BACK. In USB/SD media playback
mode, press and hold momentarily to fast forward/rewind.
14. SOURCE BUTTON
Press the Source Button to cycle through the following
sources if available: Radio: CD: USB: SD: AUX
AUDIO FUNCTIONS
All Audio functions are easily accessable on the CA-ML600.
AUDIO MENU. Press the ENCODER VOLUME CONTROL
to access the Audio Menu mode. Then press ENTER or
TUNE UP to select the Audio Function to be adjusted,
then rotate the ENCODER VOLUME CONTROL to select
the desired setting. You can always return to the previous
Audio Function by pressing the TUNE DOWN button.
REMINDER
In the AUDIO MENU, or in any menu, you can quickly exit the menu
by pressing the ESC/RGB button
EBX ON/OFF: Turn ON or OFF the EBX (Encounter Bass
Xtender) Bass Boost.
BAS Adjust the Bass level between -7 to +7.
TRE Adjust the Treble level between -7 to +7.
BAL (Balance) Adjust the balance between the right and left
speakers from 12R (full right) to 12L (full left).
FAD (Fader) Adjust the fader between the front and rear
speakers from 12R (full rear) to 12L (full front).
(SUBWOOFER)
SW ON/OFF Turn On or Off the Subwoofer RCA output.
SW LPF Subwoofer low pass crossover: 80/120/160Hz
SWAM ON/OFF In AM mode, turn ON or OFF the Sub output.
NOTE
If the Subwoofer RCA output is set to “OFF”, then the SW LPF &
SWAM functions will not be displayed.
EQUALISER OPERATION
When you activate the Equaliser, the Pre-Set Equaliser settings
override your existing Bass, Midrange & Treble Settings.
Press the Equaliser button repeatedly to cycle through
the following pre-sets: FLAT->POP->USER->DANCE-
>ROCK->CLASSIC->JAZZ->VOCAL
To return to the Bass & Treble settings that were in use before
the EQ was selected, please select the USER setting.
SYSTEM MENU
Press (MENU) to access the System Menu and press
again to select the item be adjusted, then rotate Encoder
Volume Knob to select a value / option. To exit this menu at
any time, press the ESC/RGB button
STORE (Auto store)
While in Tuner mode, press the ENCODER VOLUME CONTROL
to activate Auto Store. The six strongest stations of the selected
band will be saved in the preset channels automatically
RDS ON/OFF
While in Tuner mode, this selection turns On or Off RDS.
RDS Functions are explained in more detail on Page 8. If
RDS is set to OFF, then the RDS Functions indicated below
with an * will not appear in the System Menu
PTY* (Program Type)
Press the ENCODER VOLUME CONTROL to enter program
type, then rotate the ENCODER VOLUME CONTROL to
select the category.
AF* ON/OFF
Turn On or Off the Alternate Frequencies function.
TA* ON/OFF
Turn On or Off the Traffic Announcement function.
REG* ON/OFF
Turn On or Off the Set Region for Alternate Frequencies function
CT* ON/OFF
Turn On or Off the CT function.
LOC* ON/OFF
(Local/Distance). Use this setting to Auto Seek to strong
local stations (Local) or all stations regardless of their
strength (Distance).
AREA
Select your country/region for the tuner:
OCEANIA (Australia/New Zealand); USA; EUROPE;
RUSSIA & press ESC/RGB to save.
CLK (Clock)
To set the clock, rotate the Encoder Volume Control to set
the hours (Note “A” or “P” will be displayed in the top-right
hand of the LCD display indicating AM or PM if the Clock
is in 12H mode – see below). Press the Encloder Volume
control to select “minutes” then rotate the control to set.
CLK 12H/24H (Clock Format)
Select the time format 12H or 24H
BEEP ON/OFF
Select On or Off to activate button confirmation beep tones.