Filter
Top Products
14
|
KDC-U7056DAB/ KDC-U7056BT/ KDC-U7056BTL
English
|
15
DSP settings
4-4. Speaker setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to <Source selection> (page 10).
Press [Control] knob.
Enters the Function setting mode.
Select “Audio Control” > “Pro Setup” >
“Speaker Setting” using [Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front” Front speaker
location
“Door”, “On Dash”, “Under Dash”
“SIZE” Front speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “16cm”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“TW” Tweeter size
“None”, “Small”, “Medium”, “Large”
“Rear” Rear speaker
location
“Door”, “Rear Deck”
(“2nd Row”, “3rd Row”[1])
“SIZE” Rear speaker size
“None”, “O.E.M.”, “8cm”, “10cm”,
“12cm”, “13cm”, “16cm”, “17cm”,
“18cm”, “4x6”, “5x7”, “6x8”, “6x9”,
“7x10”
“SubWoofer” “SIZE” Speaker Size Subwoofer
“None”, “16cm”, “20cm”, “25cm”,
“30cm”, “38cm Over”
(Colored text: Factory setting)
[1] Value set when “Minivan” or “Minivan (Long)” is selected
as described in <4-3. Car type selection> (page 13).
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter” “SIZE” Tweeter size
“Small”, “Medium”, “Large”
“Mid Range” Mid Range
speaker
location
Mid range speaker location
“Door”, “On Dush”, “Under Dush”
“SIZE” Mid range speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “16cm”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“Woofer” “SIZE” Subwoofer size
“None”, “16cm”, “20cm”, “25cm”,
“30cm”, “38cm Over”
4-5. X’Over setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <4-4. Speaker setting> (page 14).
Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to <Source selection> (page 10).
Press [Control] knob.
Enters the Function setting mode.
Select “Audio Control” > “Pro Setup” >
“X’Over” using [Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front” “FC” Front high pass filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE”[1] Front high pass slope
-6, -12, -18, -24 dB/Oct
“GAIN” Front gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
“Rear” “FC” Rear high pass filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE”[1] Rear high pass slope
-6, -12, -18, -24 dB/Oct
“GAIN” Rear Gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“SubWoofer” “FC” Subwoofer low pass filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through Hz
“SLOPE”[1] Subwoofer slope
-6, -12, -18, -24 dB/Oct
“GAIN” Subwoofer gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Subwoofer phase
“REV” (180°)/ “NML” (0°)
“Tweeter” “FC” Shelving filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz
“Volume” Tweete volume
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
(Colored text: Factory setting)
[1] Displayed only when “FC” is set to ”30” - “250”.
Select a setting item using [Control] knob.
Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [1/6].
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter” “FC” Tweeter high pass filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 kHz
“SLOPE” Tweeter slope
-6, -12 dB/Oct
“GAIN” Tweeter gain
-8 ,-7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Tweeter phase
“REV” (180°)/ “NML” (0°)
“Mid LPF” “FC” Mid range low pass filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5,
Through kHz
“SLOPE” Mid range low pass slope
-6, -12 dB/Oct
“GAIN” Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Mid range phase
“REV” (180°)/ “NML” (0°)
“Mid HPF” “FC” Mid range high pass filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE” Mid range high pass slope
-6, -12 dB/Oct
“GAIN” Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Mid range phase
“REV” (180°)/ “NML” (0°)
“Woofer” “FC” Woofer low pass filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through Hz
“SLOPE” Woofer low pass slope
-6, -12 dB/Oct
“GAIN” Woofer gain
-8, -7, -6, -5, -4, -3, -2, -1, 0 dB
“PHASE” Woofer phase
“REV” (180°)/ “NML” (0°)
Select a setting item using [Control] knob.
Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [1/6].