Filter
Top Products
English
|
47
The messages shown below display your
systems condition.
EJECT: No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
➪ Load the disc magazine properly.
No CD in the unit.
➪ Insert the CD.
NO DISC: No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
TOC ERR: No disc has been loaded in the disc
magazine.
➪ Load a disc into the disc magazine.
The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
➪ Clean the CD and load it correctly.
READ ERR: • The number of files or folders which are
stored in the connected USB device is
above the limitation.
• The file system of the connected USB
device is broken.
➪ Copy the files and folders for the
USB device again referring to www.
kenwood.com/usb/. If the error
message is still displayed, initialize the
USB device or use other USB devices.
E-05: The CD is upside-down.
➪ Load the CD correctly.
BLANK: Nothing has been recorded on the MD.
NO TRACK: No tracks are recorded on the MD,
although it has a title.
NO PANEL: The faceplate of the slave unit being
connected to this unit has been removed.
➪ Replace it.
E-77: The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"E-77" code does not disappear, consult
your nearest service center.
E-99: Something is wrong with the disc
magazine. Or the unit is malfunctioning for
some reason.
➪ Check the disc magazine. And then
press the reset button on the unit. If the
"E-99" code does not disappear, consult
your nearest service center.
LOAD: Discs are being exchanged in the Disc
changer.
READING: The unit is reading the data on the disc.
.
HOLD: The protective circuit in the unit activates
when the temperature inside the
automatic disc changer exceeds 60°C
(140°F), stopping all operation.
➪ Cool down the unit by opening
the windows or turning on the air
conditioner. As the temperature falls
below 60°C (140°F), the disc will start
playing again.
IN (Blink): The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
PROTECT: The speaker wire has a short-circuit or
touches the chassis of the vehicle, and
then the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button.
NA FILE: An Audio file is played with a format that
this unit can’t support.
➪ ----
COPY PRO: A copy-protected file is played.
➪ ----
DEMO MODE: The Demonstration mode has been
selected.
➪ The <Demonstration mode Setting>
(page 34) is ON. Turn it OFF.
NO DVICE: The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
NA DVICE: An unsupported USB device is connected.
➪ For the supported USB devices, refer to
<About USB device> (page 10).
NO MUSIC/ E-15:
• Media was played that doesn’t have data
recorded that the unit can play.
• The connected USB device contains no
playable audio file.
➪ Use media that has data recorded that
the unit can play.
USB ERR: The connected USB device is rated a
current capacity higher than the allowable
limit.
➪ Check the USB device with reference to
<About USB device> (page 10).
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device and then
reconnect it. When the same message
displays again, use another USB device.