Filter
Top Products
61
206-4257
Reference: Using the TV Zoning Feature (Cont.)
Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one
Zone. See also the FTG Channel Map Editor overview on page 43.
At the same time, keep in mind that the TV Zone designations are not mutually exclusive. That is, you may
opt to place Zone restrictions on selected channels in the FTG Channel Map, but at the same time, you can
choose to congure all TVs at the site with the same Installer Menu and/or TV Setup Menu settings. For
example, an FTG Conguration (.tlx) le being used to congure the TVs at a site may contain multiple
Installer Menu and TV Setup Menu proles with different Zone assignments, as well as an FTG Channel
Map with Zone restrictions on several channels. Each TV that still has the default TV Zone 0 setting will only
be congured by the Installer Menu and/or TV Setup Menu prole(s) with a Zone 0 designation. If, on the
other hand, the TV Zone # is set to 1, the TV will rst look in the le for the LY570H Installer Menu and/or
TV Setup Menu prole(s) with a Zone 1 designation. If none of the LY570H Installer Menu and/or TV Setup
Menu proles has a Zone 1 designation, the TV will then look for the LY570H prole(s) with a Zone 0 desig-
nation. For the FTG Channel Map conguration, when the TV Zone # is set to 0, the TV will ignore any Zone
restrictions (1–8) that may be placed on channels in the FTG Channel Map. However, when the TV Zone #
is set to 1, the TV will omit any channels that have been restricted from Zone 1 in the FTG Channel Map.
Using the TV Zoning Feature with Cloning Conguration
A location-specic conguration / TLX le may be saved (Learned) from an individual TV as part of a Master
TV Setup and then be used during Teaching. For example, if the TV Zone # in the Master TV is set to 3
before Learning is initiated, the Master TV’s Installer Menu and TV Setup Menu proles will be saved with
the TV Zone 3 assignment when Learning is completed. In order to congure the Target TVs with the Zone 3
Installer Menu and TV Setup Menu proles Learned from the Master TV, you must set the TV Zone #
accordingly in the Target TVs before transferring (Teaching) the Master TV Setup. See “Set the TV Zone # in
the TV” below. Also, see “Cloning Procedures” on pages 35 to 38 for additional information on the cloning
processes. TV Zone 0 is the default TV Zone #.
Set the TV Zone # in the TV
You can set the TV Zone # in the EZ-Manager Wizard (see “EZ-Manager Wizard” on pages 12 to 18) or,
if the TV is in Pass-through Mode, via the TV’s setup menus as described below. Note that the following
procedure can only be performed while the TV is in Pass-through Mode. You will also be able to specify a
Label (North, South, East, West) and Room Number for this TV, if desired.
1. Turn ON the TV.
2. Press MENU SETTINGS on the Installer Remote, and use the arrow navigation keys to select/highlight
the OPTION menu option. Then, press OK.
3. Use the Up/Down arrows to select Zones & Room Number, and then press OK.
4. In the Zone, Label, and Room Number pop-up window, complete the appropriate elds as described
below. Use the Left/Right arrow keys on the Installer Remote to navigate between each of the elds.
• Zone: Enables you to set a TV Zone # so that the TV can be congured with Installer Menu and/or TV
Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or TV Setup Menu
settings may be provided in a .tlx le to be used either for Teaching (cloning) or FTG Mode via CPU
conguration. If the TV is being congured for FTG Mode via CPU, the TV Zone # setting also allows
the TV to omit channels that have been restricted in the FTG Channel Map.
(Continued on next page)