Filter
Top Products
8
Compatible Input Formats
The following SDI standards are supported by the V-R201-IMD-TE:
525i, 625i
1035i/60, 1035i/59.94
1080i/60, 1080i/59.94, 1080i/50
1080psF/24, 1080psF/23.98
720p/60, 720p/59.94, 720p/50
On-Screen Menu
STRUCTURE OVERVIEW
Marker 16:9
Off, 95%, 93%, 90%, 88%, 80%, 1.85:1, 2.35:1, 4:3, 14:9, 13:9
Marker 4:3
Off, 95%, 93%, 90%, 88%, 80%
Marker Backgrd
Off, 50% Gray, Black
Marker
Setup
Center Marker
Off, On
CTemp/Gamma
55K, 65K, 93K, Linear
Monochrome
Off, On
Blue Only
Off, On
Pixel to Pixel
Off, On
Aspect Ratio
4:3, Scaled 4:3, 16:9, Full Screen
Video
Config
Curtain Color
Blue, Red, Green, White, Black
Gray Levels
RGB = 000 - 255 (8 unit steps)
Function 1
Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio
Monitor, Aspect Ratio, Pixel to Pixel, CTemp/Gamma, Blue Only, Monochrome
Function 2
Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio
Monitor, Aspect Ratio, Pixel to Pixel, CTemp/Gamma, Blue Only, Monochrome
Load Config
Mfg, User 1, User 2, User 3, User 4, User 5, User 6
Save Config
User 1, User 2, User 3, User 4, User 5, User 6
Main Board
(Main board firmware version number displayed)
Keypad
(Keypad firmware version number displayed)
System
Config
CPLD
(CPLD firmware version number displayed)
IMD State
Off, On
Status Display
Off, On
OSD Tally
Off, RGY, RG, GR, IMD
LED Tally
Off, On
Anc. Time Code
Off, LTC, VITC
OSD
Config
Audio Monitor
Off, On
IMD Protocol
Marshall, Image Video, TSL v4.0, Marshall-IV
IMD ID #
000-255
IMD Group #
001-254
IMD Name (S/N)
User Defined (16 chars max.)
IMD Baud Rate
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
IMD Fixed Align
Center, Right, Left
IMD Fixed Color
Red, Green, Yellow
IMD Fixed Str
User Defined (16 chars max.)
Tally Source
Standard, Image Video HW, Image Video 422, Standard + IV422, TSL/Marshall 422
IMD
Config
IMD Tally Mode
T1, T2, T1T2, T2T1, T1-, T2-, T1T2-, T2T1-
Serial Chars
Rx, Tx
Serial Errors
P, F, O
Packets
Rec, Exe
Packet Errors
CRC, Err
Last Command
R, E
Main
Service
Software State
000:000 1010111
17
On-Screen Menu (continued)
OSD CONFIGURATION SUBMENU (continued)
■
OSD Tally
Use this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the Tally
Source selected in the IMD Configuration submenu (see page 19).
When the Tally Source is set to Standard (contact closure), OSD Tally can be set to Off, RGY, RG, or GR:
• Off On-screen tally is disabled
• RGY Red, yellow, or green tally signals are indicated at both the bottom left and bottom right corners of the
screen. Two or three colors are shown simultaneously by subdividing each tally indicator
• RG Red tally is shown at the bottom left of the screen, and green is shown at the bottom right.
• GR Green tally is shown at the bottom left of the screen, and red is shown at the bottom right.
The following diagrams show RGY, RG, and GR OSD Tally modes:
When the Tally Source is set to TSL/Marshall 422, OSD Tally can be set to Off or IMD:
• Off On-screen tally is disabled
• IMD Red, yellow, and green tally is displayed according the protocol commands. Green, red, and yellow colors
are shown individually on either the bottom left or right of the screen.
IMD Text
00:00:00:00
RG Mode: both colors activated
(red)
(red)
IMD Text
00:00:00:00
GR Mode: both colors activated
(red)
(red)
IMD Text
00:00:00:00
IMD Text
00:00:00:00
(red) (red)
IMD Text
00:00:00:00
(red)
(green)
(yellow)
(red)
(green)
(yellow)
RGY mode: single color activated RGY mode: two colors activated RGY mode: three colors activated
(red)
(green)
(red)
(green)