Filter
Top Products
E
10
n
AUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Select “ON” and then press
MENU
.
n
SETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
MONITOR
Select the installation direction of the monitor.
LANDSCAPE ............Horizontal orientation
PORTRAIT ...............Vertical orientation
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
ashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specied.
OPERATION MODE
MODE1 ......Limits the maximum brightness lower than
MODE2.
OFF IF NO OPERATION is set to ON, and
STANDBY MODE is set to LOW POWER.
(These settings can not be changed.)
MODE2 ......Will perform standard operation.
OFF IF NO OPERATION is set to OFF, and
STANDBY MODE is set to STANDARD. These
settings can be changed.
STANDBY MODE
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
HDMI SETTING
HDMI AUTO VIEW
......................... When ON is selected, the screen size is
adjusted automatically according to the
screen size control signal included in the
video signal input from the AV HDMI input
terminal.
HDMI RGB INPUT RANGE
......................... Sets the type of HDMI signals when using
the AV HDMI input mode.
When AUTO is selected, the type is set
automatically.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 18), using the remote control unit or RS-232
cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
Select ON, then press
MENU
. Perform operations with the
primary monitor.
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Congures the settings to control the monitor from the
computer via LAN. (See page 28.)
BRIGHTNESS SENSOR
(When connected to the PN-ZR01 only)
When set to ON or ON: DISPLAY, the brightness will
automatically change according to the lighting and
surrounding brightness. Performs operation with the primary
monitor. If set to ON: DISPLAY, the effect will be displayed
with a
.
If connecting to multiple monitors, the brightness of all the
monitors will change.
The
will be displayed on the primary only.
BRIGHTNESS SENSOR SETTING
(When connected to the PN-ZR01 only)
Performs adjustments to the brightness sensor. Performs
operation with the primary monitor.
Set the surrounding brightness and the current screen
luminance to AMBIENT BRIGHTNESS and SCREEN
BRIGHTNESS.
Individually set WHEN LIGHT: and WHEN DARK:.
Even if brighter or darker than the set AMBIENT
BRIGHTNESS, the screen brightness will not change.
Current AMBIENT BRIGHTNESS is shown for reference.
Menu Items