Filter
Top Products
INSTALLATION
Before installing your door, be certain that you have read and followed all of the instruc-
tions covered in the pre-installation section of this manual. Failure to do so may result in an
improperly installed door.
NOTE: Reference TDS 160 for general garage door terminology at www.dasma.com.
Fully Adjustable Flag Angles
Tools: None
1
NOTE: If you have Quick Install flag angles, skip this step.
NOTE: If you have riveted track, skip this step.
NOTE: Flag angles are right and left handed.
If you have Quick Install vertical tracks, hand tighten the left hand flag angle to the left hand
vertical track using (1) stud plate and (2) 1/4” – 20 flange hex nuts. Repeat for the other side.
If you have Fully Adjustable vertical tracks, hand tighten the left hand flag angle to the left
hand vertical track using (2) 1/4”-20 x 9/16” track bolts and (2) 1/4”-20 flange hex nuts.
Repeat for other side. Flange nuts will be secured after flag angle spacing is completed in
step, Top Section.
Quick Install
vertical
track
Stud
plate
Flag angle
1/4”-20
Flange hex nuts
1/4”- 20 x 9/16”
Track bolts
Flag angle
Fully Adjustable
vertical
track
1/4”-20
Flange hex nuts
Fully Adjustable Jamb Brackets
Tools: None
2
NOTE: If you have Quick Install jamb brackets, skip this step.
NOTE: If you have riveted track, skip this step.
NOTE: The bottom jamb bracket is always the shortest bracket, while the center jamb
bracket is the next tallest. If three jamb brackets per side are included with your door, you will
have received a top jamb bracket, which is the tallest.
To attach the bottom jamb bracket, locate lower hole of the hole/ slot pattern of the 1st hole
set on the vertical track. Align the slot in the jamb bracket with the lower hole of the hole/ slot
pattern. Secure jamb bracket using (1) 1/4”-20 x 9/16” track bolt and (1) 1/4”-20 flange hex
nut. Repeat for other side.
Place the center jamb bracket over the lower hole of the hole/ slot pattern that is centered
between the bottom jamb bracket and flag angle of the 2nd hole set. Secure jamb bracket
using (1) 1/4”-20 x 9/16” track bolt and (1) 1/4”-20 flange hex nut. Repeat for other side.
If a top jamb bracket was included, secure it to vertical track using the lower hole of the hole/
slot pattern in the 3rd hole set and (1) 1/4”-20 x 9/16” track bolt and (1) 1/4”-20 flange hex
nut. Repeat for other side.
F.A. jamb
bracket
1/4”- 20 x
9/16”
Track bolt
1/4”- 20
Flange hex nut
Jamb bracket
in place
1st hole set
Lower hole of
hole/ slot pattern
Vertical track
2nd hole set 3rd hole set
Top of track
Bottom Weather Seal
Tools: Power Drill, 7/16” Socket driver, Tape measure
3
NOTE: Refer to door section identification, located in the pre-installation section of this
manual.
Determine what size section you need to use for the bottom section. Select proper bottom
section.
Align the ends of the bottom weather seal with the bottom of the section and attach with
1/4”-14 x 7/8” self drilling screws, one on each end at least 6” from the end of the section
and one every 18” in between.
Bottom section
1/4”-14 x 7/8” Self
drilling screws
Bottom section
Bottom
weather seal
6”
18” 18”18”
6”
18”
1/4”-14 x 7/8”
Self drilling
screws
Bottom
weather seal
Counterbalance Lift Cables
Tools: Power Drill, 7/16” Socket driver, Tape measure
4
NOTE: Refer to door section identification, located in the pre-installation section of this
manual.
Starting on the left hand side, attach left hand bottom corner bracket to the left corner of the
bottom section, making sure it is seated to the edges of the end cap, with (5) 1/4”-14 x 7/8”
self drilling screws and (1) 1/4”-14 x 5/8” tamper resistant self drilling screw. Repeat for
other side.
NOTE: All doors are provided with the tamper resistant fastener for the bottom corner
brackets. However, the professional installer is most likely to have the proper tool to install
this fastener. If the homeowner does not have the proper tool to install the tamper resistant
fastener, use a regular 1/4”-14 x 7/8” self drilling screw in it’s place.
WARNING WARNING
FAILURE TO ENSURE TIGHT FIT OF CABLE LOOP OVER MILFORD PIN COULD
RESULT IN CABLE COMING OFF THE PIN, ALLOWING THE DOOR TO FALL,
POSSIBLY RESULTING IN SEVERE OR FATAL INJURY.
Uncoil the counterbalance lift cables and slip the loop at the ends of the cables over the
milford pins on the bottom section.
NOTE: Check to ensure cable loop fits tightly over the milford pins.
Insert a short stem track roller with roller spacer into the bottom corner bracket. Repeat for
other side.
NOTE: Verify bottom weather seal (bottom seal) is aligned with door section. If there is more
than 1/2” excess bottom weather seal on either side, trim bottom weather seal even with
door section.
(5) 1/4”-14 x 7/8”
Self drilling screws
Bottom section
1/4”-14 x 5/8” Tamper
resistant self drilling screw
Bottom corner
bracket
End cap
Milford pin
Bottom section
Counterbalance
cable loop
Short stem
track roller
Roller spacer
Bottom
corner
bracket
Counterbalance
lift cable
Milford pin
Bottom
weather seal
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
6