Pressure Switch Replacement
VlARN!NG: Before proceeding, follow
the
Pressure Relief
Procedure outlined on page 5. Additionally, follow all
other warnings to reduce
the
risk of an injection injury,
injury from moving parts or. electric shock.
Always
unplug the sprayer before servicing!
1.
Remove
the
two
screws
(#24)
from
bottom
of
Manifold
p.22
2.
Unscrew
nut
of
hose
(#300)
from
the
Connector
(#31 0)
p.24
3.
Remove
the
Filter/Manifold
Assembly.
(p 22)
Refer to Page
20
for the following instructions:
4.
Remove
the
Screw
(#35)
and
remove
the
Knob (#68).
5.
Remove
the
Cover
Plate
and
Insulator
(#37
& 38).
6.
Disconnect
the
red
wires
connecting
to
the
Clutch
Starter
(#42).
7.
Remove
the
screw
(#35)
located in
the
back
of
the
Electrical Box.
Insert
a
1/8"
allen
wrench
in
the
hold
and
back-
off
the
set
screw
(#44) until
the
Pressure
Switch (#43) is
able
to
slide
down
through.
Feed
the
electrical
wires
down
at
the
same
time.
8.
Insert a
new
Switch
Assembly
(#48)
into
the
housing
(#65)
while
carefully
guiding
the
wire
into
the
Switch
Box.
Using
a
needle
nose
pliers
reconnect
the
wire
to
the
Clutch Starter.
9.
Making
sure
that
the
Switch
Assembly
is full inserted,_
tighten
the
Set
Screw
(#44)
with a 1/8" allen
wrench
unt1l
the
Switch
Assembly
is
secure.
Reattach
the
Knob
(#68).
1
o.
Make
sure
that
the
Gasket
(#50) is
in
place.
Then
install
the
Manifold
Assembly
p.
22.
Secure
with
two
screws
and
reattach the Retaining
Nut
on
the
Hose
(#300)
to
the
Connector
(#310)
p.
24.
11. Install the
Cover
Plate
and
Insulator
(#37
& #38) p. 20.
12.
The
Pressure
Switch
is
factory
calibrated; no
adjustment
is
required.
Gun Filter
WARN1NG: Follow all safety precautions as described
in
high pressure warning section before proceeding. If your
spray gun
leaks or spits at the tip when you release the
trigger,
the
needle or seat
is
dirty, worn or damaged and
must be cleaned or replaced.
Replacement or Removal of Filter: .
1. First pull down on trigger safety guard and
sw1ng
away from
handle.
2.
Unscrew
handle from spray head.
3.
Unscrew
left hand threaded* filter from spray head.
(*NOTE: Left handed thread requires turning the filter clockwise
to
remove.)
4.
Screw
new
or cleaned
(t)
filter into
the
head.
To
reinstall left hand thread turn counterclockwise.
5. Reattach handle to
head
and secure safety trigger guard.
(NOTE: If filter breaks off in the head use a small
wood
screw to
remove.)
Figure
9 --
For
more
detail,
part
number
information
and
assembly
drawings
at
larger
scale,
please
see
the
LX
80
Gold
Professional
Airless
Gun
Owner's
Manual
(#313-687).
5 Gal (55 Gal) Swivel Syphon Hose
(Low Rider Pump)
781-060 SYPHON HOSE (COMPLETE) INCLUDES ITEMS 1-6
3
4
ITEM NO
PART NO
DESCRIPTION
QTY
1
710-081
Adapter
2
757-068
Syphon Tube
7
(Includes Item #7)
*3
783-043
Bypass Hose 5
Gal.
5
*4
710-203
Syphon Hose 5 Gal.
~
5
730-334
Clip
6
710-046
Inlet
Screen
7
710-196
0-Ring
1
6
~
8
710-219
Bypass Hose 55 Gal.
Opt.-.
9
783-043
Syphon Hose 55 Gal. Opt.
2
23
