Filter
Top Products
21
ignition on and unit off, the timer even turns the unit on and goes to the specified frequency. Press
<< or >> to turn Tuner Timer on or off.
Radio Monitor (“RM ON” & RM OFF”)
Allows radio to play during tape winding or scan. If this feature has been
activated, RM icon appears when tape is in use.
Blank Skip Time (“BSKPTIME”)
When unit reaches a blank section of tape, it can automatically fast-forward to next recorded
section. Use << and >> to choose minimum amount of blank time before blank skip begins from
between 1 to 16 seconds. SUGGESTION: Classical music listeners may want to specify a longer
blank, so that the unit doesn’t mistake soft passages for blank spots.
Blank Skip Activation
Press << or >> to turn Blankskip on or off.
Scan Times
You can set different scan times for Radio (“RD SCNTM”), Cassette (“TP SCNTM”), and Changer
(“CD SCNTM”) between 1 and 16 seconds. Press << or >> to adjust scan time.
Confirmation Beep On/Off (“BTTNBEEP”)
To activate or defeat beep for all button presses, press << or >>. (Button presses requiring more
than 1/2 second always have confirmation beep.)
Adjustable Mute Level (“MUTE LVL”)
The unit’s mute level can be adjusted to any volume level. This mute level also applies to cellular
mute. During Menu mode, once “MUTE LVL” appears, actual mute level is heard. Adjust the mute
level volume by using <</>>, NOT + and –. (If mute is activated when unit volume level is lower
than mute level, unit volume level is maintained, even though “MUTE” appears.
Maximum Turn-On Volume Level (“MAXONVOL”)
Sets maximum volume that is heard when unit is turned on. (Once “MAXONVOL” appears, actual
MAXONVOL level is heard.) Adjust the MAXONVOL volume by using <</>>, NOT + and –. If unit is
turned off while volume is louder than MAXONVOL, turn-on volume will be at MAXONVOL level.
However, if unit is turned off when volume level is lower than MAXONVOL, turn-on volume will be
at level it was when unit was turned off.
Loudness Levels
You can choose between two loudness settings for each audio source: “LOUD TAPE”, “LOUD
AUX”, “LOUD CD”, (for CD Changer) “LOUD AM” and “LOUD FM”. “LOUD 1” provides up to 8 dB
boost in bass (centered at 60 Hz) and up to a 2 dB boost in treble (centered at 8 KHz). “LOUD 2”
provides up to 12 dB boost in bass (centered at 60 Hz) and up to a 4 dB boost in treble (centered at
8 KHz). To set the loudness level for each source, use << and >>.
Radio Station Naming (“STN NAME”)
Available only while radio is active source. One name per frequency, 8 characters per name.
(Names can be assigned to any frequency, preset or not.) If you try to enter more than 30 names,
“**FULL**” appears. You can then enter new names after erasing some of existing names.
To store station names:
1. Press DIS for more than 2 seconds to enter Menu mode.
2. Scroll to Radio Station Naming feature by pressing /\ / V .
3. Enter Station Name Access mode by pressing << or >> button.
4. Tune to desired station using AM, FM, presets or /\ / V buttons. If previously named, name appears.
5. Press << or >> buttons to enter Station Name Edit mode.
6. Press /\ / V to select character. Select “__“ for a blank space.
7. Press << or >> buttons to select next character position.
8. Press Mute to store name. Display blinks STORING twice before return to Station Access mode.
9. To name another station, repeat steps 4-8.
10. To return to Menu, press Mute again.
(There is no time-out from Station Name Access & Edit modes.)
Display Priority & Radio Station Names- See Display Options on page 13.