Filter
Top Products
SC-411RD-10 Installation and Operating Instructions Page 7 of 12
CP5094C 7/30/12
Option Set 1
S1 (CUTOUT Input), S2 (SIRCTRL Input),
S3 (LITCTRL Input) - These inputs are
normally activated by a 12V input (ON).
Press the switch once until it FLASHES to
change to ground activation. Press the
switch again for OFF to disable.
S4 (Timed Override) - While In Wail, Yelp or
Phaser mode, momentarily pressing the
Manual push button will override the Wail,
Yelp or Phaser tone. With this option ON
the unit automatically goes back to the
previous tone after 10 seconds.
S5 (Sweep/Intersection Function) - While in
Wail, Yelp, or Phaser mode, momentarily
activating the siren control input will change
the unit into sweep and intersection mode.
S6 (Automatic Siren Enable) The Auto-
matic Siren feature on the Lever switch
Position 3 may be enabled with this switch.
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Option Set 2
S1 (Two-Tone Enable) - Two-Tone replaces
Phaser tone when turned ON.
S2 (Phaser/Two-Tone Disable) - Phaser
and Two-Tone are disabled when ON.
S3 (Short Manual Enable) - The Manual
siren tone will normally die out and stop
when Manual push-button is released.
Turning option ON forces the Manual siren
tone to stop immediately.
S4 (Horn Disable) - Horn tone is disabled
when turned ON.
S5 (Lever 2 Isolated) - Turn ON for L2
output only in Lever switch position 2.
S6 (Lever 3 Isolated) - Turn ON for L3
output only in Lever switch position 3.
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Option Set 3
S1 (Alert Enable) - Turn off to disable Alert
feature (reminder beep).
S2 (Lever/Siren Video) - VIDEO output is
normally on when the Lever switch and/or
Siren is active. Press switch to disable.
(NOTE: this does not control the VIDEO
Output for S1 - S6. See S1 - S6 Operation)
Press the OUT/DIM button momentarily to move into next section, or OUT/DIM for 3 seconds to save & exit.
Second Tone Control
Press S1, S2, S3 or S4 to select the second speaker tone when in the corresponding Function switch setting.
Press the OUT/DIM button momentarily to go back to beginning, or OUT/DIM for 3 seconds to save & exit.
NOTE: These option setting can be easily transferred to another vehicle. See PROGRAM TRANSFER.
Press Lever Switch = OFF Shows blinking
0↓
S1
On (Default) Cutout Input Active +
1↓ Flash Cutout Input Active -
2 Off Cutout Input Off
0↓
S2
On (Default) Siren Control Input Active +
1↓ Flash Siren Control Input Active -
2 Off Siren Control Input Off
0↓
S3
On (Default) Light Control Input Active +
1↓ Flash Light Control Input Active -
2 Off Light Control Input Off
0↓
S4
Off (Default) Timed Override Off
1 On Timed Override On
0↓
S5
Off (Default) Sweep/Intersection Off
1 On Sweep/Intersection On
0↓
S6
On (Default) Automatic Siren On
1 Off Automatic Siren Off
Press Lever Switch = OFF Shows blinking
0↓
S1
Off (Default) Phaser
1 On Two-Tone Replace
0↓
S2
Off (Default) Phaser/Two-Tone Enable
1 On Phaser/Two-Tone Disable
0↓
S3
Off (Default) Normal Manual
1 On Short Manual
0↓
S4
Off (Default) Horn Enable
1 On Horn Disable
0↓
S5
Off (Default) Lever 2 Progressive
1 On Lever 2 Isolated
0↓
S6
Off (Default) Lever 3 Progressive
1 On Lever 3 Isolated
Press Lever Switch = OFF Shows blinking
0↓
S1
On (Default) Alert Enabled
1 Off Alert Disabled
0↓
S2
On (Default) Lever/Siren Video Enabled
1 Off Lever/Siren Video Disabled
Rotary
Position
Lever Switch = OFF Shows & blinking
S1 S2 S3 S4
WAIL
2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone
YELP
2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone
PHSR
2
nd
= Wail 2
nd
= Yelp 2
nd
= Phaser 2
nd
= Two-Tone