Filter
Top Products
Bluetooth telephonedata can bedeleted. To pro-
tect personalinformation, werecommend deleting
this databefore transferring the unitto other per-
sons. Thefollowing settings will bedeleted.
! phone bookentries on theBluetooth tele-
phone
! preset numberson the Bluetoothtelephone
! registration assignmentof the Bluetooth tele-
phone
! call history of theBluetooth telephone
! information of theconnected Bluetooth tele-
phone
1 Press M.C. toshow the confirmationdisplay.
YES isdisplayed. Clearing memory is nowon
standby.
If you donot want toreset phone memory,
press
. Thedisplay reverts.
2 Press M.C. toclear the memory.
CLEARED isdisplayed and thesettings are de-
leted.
! While thisfunction is in use,do not turn
off the engine.
VER INFO(Bluetooth version display)
You can displaythe system versionsof this unit
and ofBluetooth module.
1 Press M.C. todisplay the information.
S/W UPDATE(updating the software)
This functionis used to updatethis unit withthe
latest software. For information onthe software
and updating,refer to our website.
! Never turnthe unit off whilethe software is
being updated.
1 Press M.C. todisplay the datatransfer mode.
Followthe on-screen instructionsto finish up-
dating thesoftware.
Using an AUX source
1 Insert the stereo mini pluginto the AUX
input jack.
2 Press S(SRC/OFF) to select AUXas the
source.
Note
AUX cannot be selected unless theauxiliary set-
ting is turned on. For more details, refer to AUX
(auxiliary input) on the previous page.
Turning the clock display on
or off
% Press to turn the clockdisplay on or
off.
# The clockdisplay disappears temporarilywhen
you perform otheroperations, but the clockdisplay
appears againafter 25seconds.
Connections
WARNING
! Use speakers over 50 W (output value) and
between 4 W to 8 W (impedance value).Do
not use 1 W to 3 W speakers forthis unit.
! The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wirefirst.
Ensure that the ground wire is properly con-
nected to metal parts of the car’s body. The
ground wire of the power amp and the oneof
this unit or any other device must becon-
nected to the car separately with different
screws. If the screw for the ground wire loos-
ens or falls out, it could result in fire, genera-
tion of smoke or malfunction.
Ground wire
Metal parts of car’s bod
y
POWER AMP
Other devices
(Another electronic
device in the car)
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cableto the
terminal that detectsoperation of the ignition
key may result in battery drain.
O
N
S
T
A
R
T
O
F
F
ACC position NoACC position
! Use this unit with a 12-volt battery and nega-
tive grounding only. Failure todo so may re-
sult in a fire or malfunction.
! To prevent a short-circuit, overheatingor mal-
function, be sure to follow thedirections
below.
— Disconnect thenegative terminal ofthe bat-
tery before installation.
— Secure thewiring with cableclamps or adhe-
sive tape.Wrap adhesivetape around wiring
that comesinto contact with metalparts to
protect thewiring.
— Placeall cables away frommoving parts,
such asthe gear shift andseat rails.
— Placeall cables away fromhot places, such
as nearthe heater outlet.
— Donot connect theyellow cable tothe battery
by passingit through thehole to the engine
compartment.
— Coverany disconnected cable connectors
with insulatingtape.
— Do notshorten any cables.
— Nevercut the insulation ofthe power cableof
this unitin order to sharethe power with
other devices.The current capacityof the
cable islimited.
— Usea fuse of therating prescribed.
— Never wirethe negative speakercable directly
to ground.
— Neverband together negative cablesof multi-
ple speakers.
! When this unit is on, control signalsare sent
through the blue/white cable. Connect this
cable to the system remote control of anex-
ternal power amp or the vehicle’s auto-anten-
na relay control terminal (max. 300 mA 12V
DC). If the vehicle is equipped with a glass
antenna, connect it to the antenna booster
power supply terminal.
! Never connect the blue/white cable tothe
power terminal of an external power amp.
Also, never connect it to thepower terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
English
Operating this unit
03
11
Section
Installation
En