9. Repeat for other similar corner
bracket. These brackets, (G) Fig. 13
are where the rubber leveling feet will
be installed.
10. The brackets with the open end, as
shown at (M) Fig. 14, are attached
in a similar manner as described in
Steps 6 to 9. NOTE: MAKE SURE
THE OPEN END IS ALIGNED
AS SHOWN IN FIGS. 14 AND 15.
THE WHEELS WILL BE INSTALL
ED INSIDE THESE BRACKETS,
AS SHOWN IN FIG. 20.
LEVELING FEET
11. Take leveling feet (shown at 33 in Fig.
3) and thread one
5
/16-18 Hex Jam Nut
all the way onto the screw post. Insert
screw post into hole of enclosed
corner bracket as shown in Fig. 17.
Place another
5
/16-18 Hex Jam Nut
onto the post and tighten. Move hex
nuts up or down post to adjust the
height of the foot. Repeat for the other
leveling foot.
WHEELS
12. Place a wheel (N) Fig. 19 in an open
end bracket (O) Fig. 19. Insert a
5
/16-18
x 2
1
/4” Hex Head Cap Screw (No. 26
in Fig. 4) through the bracket and the
wheel. Fasten it together as shown in
Fig. 19 with a
5
/16-18 Nylok Nut (P).
13. Fig. 20 shows the leveling feet and the
wheels properly assembled.
14. NOW, TIGHTEN ALL HARDWARE.
Tighten panels first, and then leg
supports.
ATTACHING FOOT LEVER ASSEMBLY
TO BASE
The Foot Lever and Caster Assembly are
assembled together by placing the Foot
Lever (R) over the Caster Assembly (S)
Fig. 21 and lining up the holes (T) and (U).
Then, insert a
5
/16-18 x 4” Hex Head Screw
though hole (T) and fasten in place with a
5
/16-18 Nylock Nut (V) Fig. 22.
Assemble the Foot Lever to the base by
lining up the three holes in the Foot Lever
(W) Fig. 23 with the three holes in the base
(X) Fig. For each hole, place an M8 Flat
Washer on an M8 x 20 Hex Head Screw
and insert screw into hole. Then fasten to
base by placing an M8 Flat Washer, M8
Lock Washer and M8 Hex Nut onto the
screw and tighten.
12
Fig. 17
Fig. 18
Fig. 15
M
Fig. 19
N
O
P
Fig. 20
Q
R
S
T
U
Fig. 21
V
Fig. 22
W
X
Fig. 24
Y
Fig. 23
PLASTIC FEET
Install the Plastic Feet (Y) Fig. 24 by placing them around radius at end of legs as shown.
Tap the feet in place with a soft hammer or using a regular hammer and a block of wood.
ADDING AN OPTIONAL SHELF
If you desire, you can install a shelf made from a piece of
3
/4-inch plywood measuring 22
3
/8”
x 19
1
/4” (568.96 mm x 488.95 mm). To install, screw the wood to the leg supports through
the (8) holes in the leg supports, six of which are shown at (Q) Fig. 20. When the saw is
upside down (as in Fig. 20) the shelf would be placed underneath the overhangs of the
leg supports. When the saw is flipped right-side up, the shelf would be on top of the leg
support overhangs. To install the shelf, it will be necessary to remove one side panel. Make
sure this panel is re-installed before using the saw. See exact measurements for shelf in
the back of this manual.
