© Titan Tool Inc. All rights reserved. 5
Preparing to Paint
Before painting, it is important to make sure that the uid in the
system is compatible with the paint that is going to be used.
NOTE: Incompatible uids and paint may cause the valves
to become stuck closed, which would require
disassembly and cleaning of the sprayer’s uid
section.
IMPORTANT: Always keep the trigger lock on the spray gun in
the locked position while preparing the system.
1. Place the siphon tube into a container of the appropriate
solvent for the material being sprayed (refer to
recommendations of the material manufacturer). An example
of an appropriate solvent is water for latex paint.
2. Place the return hose into a metal waste container.
3. Move the PRIME/SPRAY valve down to the
PRIME position.
NOTE: Hold the return hose in the waste
container when moving the PRIME/
SPRAY valve to PRIME in case the
sprayer is pressurized.
On/O
Clean
Min.
PSI
(Bar)
Max. PSI
(Bar)
S
p
r
a
y
L
a
t
e
x
P
a
i
n
t
s
&
H
e
a
v
i
e
r
C
o
a
t
i
n
g
s
S
p
r
a
y
C
l
e
a
r
s
,
L
a
c
q
u
e
r
s
&
E
n
a
m
e
l
s
4. Set the pressure to minimum by turning
the pressure control knob to the “MIN PSI”
setting in the yellow zone.
5. Allow the sprayer to run for 15–30 seconds
to ush the old solvent out through the
return hose and into the metal waste
container.
6. Turn o the sprayer by moving the pressure control knob to
the OFF position in the black zone.
NOTE: Make sure that the spray gun does not have a tip or
tip guard installed.
7. Move the PRIME/SPRAY valve up to the
SPRAY position.
8. Set the pressure to minimum by turning
the pressure control knob to the “MIN PSI”
setting in the yellow zone.
9. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against
the edge of the metal container
while flushing. Failure to do so may
lead to a static electric discharge,
which may cause a fire.
10. Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
11. Lock the gun by turning the gun trigger lock to the locked
position.
12. Set down the gun and increase the pressure by turning the
pressure control knob slowly clockwise into the green zone.
13. Check the entire system for leaks. If leaks occur, turn o the
sprayer and follow the “Pressure Relief Procedure” in this
manual before tightening any ttings or hoses.
14. Follow the “Pressure Relief Procedure” in this manual before
changing from solvent to paint.
Be sure to follow the pressure relief procedure when
shutting down the sprayer for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for
cleanup.
Painting
1. Place the siphon tube into a container of paint.
2. Place the return hose into a metal waste container.
3. Move the PRIME/SPRAY valve down to the
PRIME position.
NOTE: Hold the return hose in the waste
container when moving the PRIME/
SPRAY valve to PRIME in case the
sprayer is pressurized.
On/O
Clean
Min.
PSI
(Bar)
Max. PSI
(Bar)
S
p
r
a
y
L
a
t
e
x
P
a
i
n
t
s
&
H
e
a
v
i
e
r
C
o
a
t
i
n
g
s
S
p
r
a
y
C
l
e
a
r
s
,
L
a
c
q
u
e
r
s
&
E
n
a
m
e
l
s
4. Turn the unit on and set the pressure to
minimum by turning the pressure control
knob to the “MIN PSI” setting in the
yellow zone.
5. Allow the sprayer to run until paint is
coming through the return hose into the
metal waste container.
6. Turn the unit o by moving the pressure control knob to the
OFF position in the black zone.
7. Remove the return hose from the waste container and place it
in its operating position above the container of paint.
8. Move the PRIME/SPRAY valve up to the
SPRAY position.
9. Turn the unit on and set the pressure to
minimum by turning the pressure control
knob to the “MIN PSI” setting in the yellow
zone.
10. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against
the edge of the metal container
while flushing. Failure to do so may
lead to a static electric discharge,
which may cause a fire.
11. Trigger the gun into the metal waste container until all air and
solvent is ushed from the spray hose and paint is owing
freely from the gun.
12. Lock the gun by turning the gun trigger lock to the locked
position.
13. Turn the unit o by moving the pressure control knob to the
OFF position in the black zone.
14. Attach tip guard and tip to the gun as instructed by the tip
guard or tip manuals.
POSSIBLE INJECTION HAZARD. Do not spray without
the tip guard in place. Never trigger the gun unless
the tip is in either the spray or the unclog position.
Always engage the gun trigger lock before removing,
replacing or cleaning tip.
15. Turn the unit on and set the pressure to minimum by turning
the pressure control knob to the “Min PSI” setting in the
yellow zone.
16. Increase the pressure by turning the pressure control knob
slowly clockwise and test the spray pattern on a piece of
cardboard. Adjust the pressure control knob until the
spray from the gun is completely atomized. Try to keep the
pressure control knob at the lowest setting that maintains
good atomization.
NOTE: Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear and
additional overspray.
