Filter
Top Products
16-EN
Adjusting Subwoofer Level/Bass Level/
Middle Level/Treble Level/Balance (Between
Left and Right)/Fader (Between Front and
Rear)/Loudness/Defeat
1
Press AUDIOSETUP repeatedly to choose the desired
mode.
Each press changes the mode as follows:
SUBWOOFER
*1
BASS LEVEL
*2
MID LEVEL
*2/*4
TRE LEVEL
*2
BALANCE FADER LOUDNESS
*2/*3/*4
DEFEAT VOLUME
SUBWOOFER
*1 When the subwoofer mode is set to OFF, its level cannot be
adjusted.
*2 Adjustable only when DEFEAT is OFF.
*3 For details about loudness, refer to “Turning Loudness On/Off
(CDE-HD137BT Only)” on page 17.
*4 Only for CDE-HD137BT.
*5 Only for CDE-HD138BT.
Setting value will change according to the level value set in
BAND1 of P-EQ or G-EQ. Refer to “Adjusting the Parametric
Equalizer Curve (5BAND P.EQ) (CDE-HD138BT Only)” on
page 17 or refer to “Adjusting the Graphic Equalizer Curve
(7BAND G.EQ) (CDE-HD138BT Only)” on page 17.
*6 Only for CDE-HD138BT.
Setting value will change according to the level value set in
BAND5 of P-EQ or BAND7 of G-EQ. Refer to “Adjusting the
Parametric Equalizer Curve (5BAND P.EQ) (CDE-HD138BT
Only)” on page 17 or refer to “Adjusting the Graphic Equalizer
Curve (7BAND G.EQ) (CDE-HD138BT Only)” on page 17.
Note
• If no operation is performed for 5 seconds, the unit automatically
returns to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS, MID,
TRE LEVEL and LOUDNESS will return to the factory defaults.
Audio Setup
You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
1
Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select AUDIO, and then press
ENTER.
AUDIO GENERAL DISPLAY TUNER SIRIUSXM
*6
iPod
BLUETOOTH
3
Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
(e.g. Select SUBWOOFER)
FACTORY EQ
*1/*2
LOUDNESS
*1/*2
EQ MODE
*2/*6
5BAND P.EQ
*2/*3
7BAND G.EQ
*2/*4
MX SETTING
*2
3BAND EQ
*1
VOL LV ADJ HPF
*2
SUBWOOFER
SUBW LPF
*5
SUBW PHASE
*5
SUBW SYS
*5
POWER IC
*1 Only for CDE-HD137BT.
*2 Adjustment cannot be performed when DEFEAT is set to ON.
*3 Only for CDE-HD138BT.
Displayed when EQ MODE is set to 5BAND P.EQ.
*4 Only for CDE-HD138BT.
Displayed when EQ MODE is set to 7BAND G.EQ.
*5 These functions are inoperable when Subwoofer is set to OFF.
*6 Only for CDE-HD138BT.
4
Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select SUBW ON or SUBW OFF)
5
Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
•Pressing returns to the previous Sound menu mode.
• Pressing and holding for at least 2 seconds will return to normal
mode.
• If no operation is performed for 60 seconds, Sound menu mode is
canceled.
Sound Setting
Subwoofer +0 ~ +15
Bass level −7 ~ +7
*4
/ −6 ~ +6
*5
Middle level −7 ~ +7
*4
Treble level −7 ~ +7
*4
/ −6 ~ +6
*6
Balance L15 ~ R15
Fader R15 ~ F15
Loudness ON/OFF
Defeat ON/OFF
Volume 0 ~ 35
AUDIO/SETUP
Rotary encoder/ /ENTER
Use steps 1 to 5 to select the category you wish to modify. For
details on how to change each setting, see the following
sections below.