Filter
Top Products
17-EN
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Setting item: FACTORY EQ
Setting contents:
USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /
ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL
Loudness introduces a special low-and high-frequency emphasis at low
listening levels. This compensates for the ear’s decreased sensitivity to
bass and treble sound.
Setting item: LOUDNESS
Setting contents:
OFF (Initial setting) / ON
This setting gives you a choice of 5-band parametric, or 7-band graphic
equalizer.
Setting item: EQ MODE
Setting contents:
5BAND P.EQ (Initial setting) / 7BAND G.EQ
5BAND P.EQ:
5-band Parametric EQ.
7BAND G.EQ:
7-band Graphic EQ.
The Parametric EQ function gives more flexibility than the Graphic EQ
in covering problem areas in the vehicles response curve.
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
1
Turn the Rotary encoder to select the Band, and then
press ENTER.
BAND1 BAND2 BAND3 BAND4 BAND5
2
Turn the Rotary encoder to select the desired item, and
then press ENTER.
WIDTH (Q) CENTER FRQ LEVEL
Setting the Bandwidth (WIDTH (Q))
3-1
Turn the Rotary encoder to select the desired bandwidth.
WIDE 1 (Initial setting) MEDIUM 2 MEDIUM 3 NARROW 4
Change the boosted bandwidth to wide or narrow. A wider setting will
boost a wide range of frequencies above and below the center frequency.
A narrower setting will boost only frequencies near the center
frequency.
Setting the Center Frequency (CENTER FRQ)
3-2
Turn the Rotary encoder to select the desired center
frequency.
BAND1: 63/80/100/200 (63 Hz)
BAND2: 160/250/400/630/1.0 K (160 Hz)
BAND3: 630/1.0 K/1.6 K/2.5 K/4.0 K (630 Hz)
BAND4: 1.6 K/2.5 K/4 K/6.3 K/10.0 K (1.6 KHz)
BAND5: 10.0 K/12.5 K/16 K/17.5 K (10.0 KHz)
Setting the Level
3-3
Turn the Rotary encoder to select the desired level
(−6 ~ +6).
4
Repeat steps 1 to 3 to adjust other Bands.
Notes
•Press to return to the previous step.
• The frequency range of adjacent bands should not overlap.
• While adjusting the Parametric EQ, you should consider the frequency
response of the connected speakers.
• Using the Parametric EQ disables the Graphic EQ function.
The Graphic EQ is simpler to set up and use compared to the Parametric
EQ.
You can modify the equalizer settings to create a response curve more
appealing to your personal taste.
1
Turn the Rotary encoder to select the desired band, and
then press ENTER.
BAND1 80 BAND2 250 BAND3 500 BAND4 1.0 K
BAND5 4.0 K BAND6 8.0 K BAND7 16.0 K
2
Turn the Rotary encoder to select the desired level
(−6 ~ +6), and then press ENTER.
3
Repeat steps 1 to 2 to adjust other Bands.
Notes
•Press to return to the previous step.
• Using the Graphic EQ disables the Parametric EQ function.
Equalizer Presets (F-EQ)
(CDE-HD137BT Only)
Turning Loudness On/Off
(CDE-HD137BT Only)
Setting EQ mode (CDE-HD138BT Only)
Adjusting the Parametric Equalizer Curve
(5BAND P.EQ) (CDE-HD138BT Only)
Adjusting the Graphic Equalizer Curve
(7BAND G.EQ) (CDE-HD138BT Only)