Filter
Top Products
VRX835 37
English
Owner’s manual
DSP operations
2. Touch the [z] key to select “POSI. DETAIL”.
Touch the [POSI. DETAIL] key to show Posi-
tion Detail adjusting display.
3. Touch the [w] or [z] key to adjust to a de-
sired fader.
Adjusting range of the fader: front 9/rear 9
4. Touch the [Î] or [Å] key to adjust to a de-
sired balance.
Adjusting range of the balance: left 9/right 9
5. When the adjustment is finished, press the [A-
M] button again or touch the [RTN] key two
times to return to the STANDARD display.
Standard mode/G.EQ operations
Note:
• The adjustment made in standard mode is not re-
flected in the adjustment in professional mode.
Respectively, the adjustment made in profes-
sional mode is not reflected in the adjustment in
standard mode.
G.EQ effect ON/OFF
∗ The factory default setting is “ON”.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [G.EQ ON/OFF] key to select “on”
and “off”.
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD display.
Note:
• If the G.EQ effect is set to OFF, the adjustment
made in “G.EQ operations” is not reflected in the
music source.
Calling G.EQ BASIC Pattern/USER
Pattern
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [G.EQ BASIC] and [G.EQ USER]
key to show BASIC pattern selecting display
or USER pattern selection/memory display.
3. In the pattern selecting display, touch the one
of pattern key and called the desired G.EQ
pattern.
In this display, pressing the No. button in cor-
respondence to the [DIRECT] key can also
call the G.EQ pattern.
∗ After selecting the G.EQ pattern, touch the
[MEMO] key to copy the selected pattern to
the USER pattern.
∗ Touch the [EDIT] key to show G.EQ adjusting
display, in which the properties of currently
selected pattern can be adjusted.
∗ By pressing the [BAND] button in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch
between the two patterns, BASIC and USER.
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
Setting and storing G.EQ Properties/
Memory into USER Pattern
1.
Repeat the steps 1 and 2 of the previous proce-
dure (Calling G.EQ BASIC pattern/USER pat-
tern) to show BASIC pattern selecting display
or USER pattern selection/memory display.
2. Touch the [EDIT] key to show the G.EQ ad-
justing display.
3. When some frequency to be adjusted is se-
lected by touching the [Î] key or [Å] key (or
the frequency key) in the G.EQ adjusting dis-
play, a gain setting value at the selected fre-
quency is displayed.
There are “50Hz”, “100Hz”, “200Hz”,
“400Hz”, “1kHz”, “3kHz” and “12kHz” avail-
able for the adjustment frequency.
4. Touch the [w] or [z] key to adjust the G.EQ
GAIN. The adjustment range is from -12 dB
to +12 dB.
5. After making adjustments to a desired pat-
tern by repeating the operations of items 3
and 4, touch the [RTN] key to change over to
the BASIC/USER pattern selection/memory
display.
6. Press and hold one of [DIRECT] buttons for
2 seconds or longer to store the adjusted
G.EQ pattern to be USER memory.
7. To set a title of the stored USER pattern,
touch the [TITLE] key to change into the
[TITLE INPUT] key.
∗ For title inputting method, refer to the section
“Entering titles”.
8. Press the [A-M] button to change into the
STANDARD display.