Filter
Top Products
4
REMOTE CONTROL FUNCTIONS
The RCP 6 remote is capable of controlling 11 devices, including the
AVR 247 and the DVD 38 included in the CP 60 system. During the
installation process, you may program the codes for each of your source
components into the remote. Each time you wish to use the codes for
any component, first press that component’s selector. This changes the
button functions to the appropriate codes for that product.
NOTE: Several of the Input Selectors are shared between two
devices. The selector button will light in red when the remote is in
the device mode printed on the button, and it will light in green for
the device mode printed above the button. To switch between the
two device modes, press the selector
twice
quickly in succession.
The selector will remain in the last-selected mode until the next
time you press it twice quickly.
For example, the first time you press the DVD Button, the button
will light in red, indicating that the remote is in DVD mode. If you
press another selector, such as the VID3 Selector, and then press
the DVD Button again, the DVD Button will remain red, indicating
the remote is still in DVD mode. Now press the DVD Button twice
quickly. At the first press the button will light in red, indicating that
the remote is in DVD mode. On the second press the button will
turn green, indicating that the remote is now in CD mode. If you
press a different selector and return to the DVD/CD Selector, you
will observe that the remote is still in CD mode.
Each Input Selector has been preprogrammed to control certain types
of components, with only the codes specific to each brand and model
changing, depending on which product code is programmed. The
device types programmed into each selector (except HDMI 1 and 2)
may not be changed.
DVD: Controls DVD players and recorders. The DVD Button functions
are labeled in blue on the remote.
CD: Controls CD players and recorders.
Tape: Controls cassette decks.
The Bridge/DMP: Controls an iPod
®
docked in The Bridge.
Video 1: Controls VCRs, TiVo
®
and DVRs.
Video 2: Controls cable and satellite television set-top boxes.
Video 3: Controls televisions and other video displays.
Video 4: Controls a TV connected to the front-panel inputs.
HDMI 1 and 2: Each code set controls a source device (such as
a VCR/PVR, DVD player or cable/satellite set-top box) connected to
one of these two inputs.
XM: Controls the AVR functions for XM
®
Satellite Radio.
For example, if you have inserted a disc in your CD player and you
would like to skip ahead three tracks, but you then find that the volume
is too loud, you would follow this procedure:
1. Press the CD Input Selector to switch to the codes that control your
CD player. If the remote is in DVD mode, press the selector twice quickly
to switch to CD mode, indicated by the selector turning green.
2. Press the Play Button (in the Transport Controls section) if the disc
is not already playing.
3. Press the Skip Up Button three times to advance three tracks.
4. Press the AVR Button so that you can access the volume controls.
5. Press the Volume Down Button until the volume level is satisfactory.
Any given button may have different functions, depending on which
component is being controlled. The buttons are labeled with some of
these functions, with the receiver’s functions shown in gray, and the
DVD player’s functions shown in blue. For example, the Sleep and DSP
Surround Buttons are labeled for use as Channel Up/Down Buttons
when controlling a television or cable box. See Table A1 in the Appendix
for listings of the different functions for each type of component.
NOTE: Although we have described the applicable DVD functions
in this section, we strongly recommend that you review the
DVD 38 manual for more information about using these functions.
IR Transmitter Lens: As buttons are pressed on the remote,
infrared codes are emitted through this lens. Make sure it is pointing
toward the component being operated.
Power On Button: Press this button to turn on the AVR or another
device. The Master Power Switch on the AVR 247’s front panel must
be switched on first.
Mute Button: Press this button to mute the AVR 247’s speaker and
headphones outputs temporarily. To turn off muting, press this button
or adjust the volume. Muting is also canceled when the receiver is
turned off.
Program Indicator: This LED lights up or flashes in one of three colors
as the remote is programmed with codes.
Power Off Button: Press this button to turn off the AVR 247 or
another device.
AVR Selector: Press this button to switch the remote to the codes
that operate the receiver.
Input Selectors: Press one of these buttons to select a source
device, which is a component where a playback signal originates (e.g.,
DVD, CD, cable TV, satellite or HDTV tuner). This will also turn on the
receiver (if it is not already on) and switch the remote’s mode to operate
the source device.
AM/FM Button: Press this button to select the tuner as the source,
or to switch between the AM and FM bands.
6-/8-Channel Input Selector: Press this button to select the
6-/8-Channel Inputs as the audio source. The receiver will use the video
input and remote control codes for the last-selected video source.
XM Radio Button: Press this button to select XM Satellite Radio as
the source. You will need to have purchased and activated an XM antenna
module, and you will also need to subscribe to the XM Satellite Radio
service. Visit www.xmradio.com for more information.
RCP 6 om.qxd 3/15/07 11:19 AM Page 4