Kenwood BT948HD Car Stereo System User Manual


  Open as PDF
of 76
 
46
|
KDC-X995/ KDC-BT948HD
DSP Setup
7
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- Car Type Selection (page 44)
- Speaker Setting (page 44)
- Car Type Fine Adjustments (page 45)
- X’Over Setting (page 46)
-ManualEqualizerControl(page41)
- Listening Position Selection (page 42)
- Listening Position Fine Adjustments (page 42)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Preset” > “Memory”.
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• Register2patternsofAudioPresetMemory.
• Presetnumber“1”:
When you press the Reset, all the sources will be the
setting value which is registered.
• Presetnumber“1”and“2”:
The memory cannot be erased by the Reset button.
• ThisfunctioncannotberegisteredwhentheiPod
Equalizer set in <PresetEqualizercurveSelect>(page41).
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 44).
Display Item Range
“X’Over”
“Front” “FC”
Front High Pass Filter
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
“SLOPE”*
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear” “FC”
Rear High Pass Filter
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
“SLOPE”*
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC”
Subwoofer Low Pass Filter
30*, 40, 50*, 60, 70, 80, 90*, 100,
120, 150, 180, 220, 250*, Through
(Hz)
“SLOPE”*
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
* Function of KDC-X995
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “X’Over”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the item you want to set
Operation type Operation
Selects the item. Turn the [VOL] knob.
Adjust each item. Press the [
4
] or [
¢
] button.
Set the value Press the [VOL] button.
6
Repeat steps 3 to 4 to complete the X’Over
settings.
 previous next