Filter
Top Products
28
206-4118
Installer Menu (Cont.)
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the Channel-Time display. Set
to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set according to Color Chart:
0 = Black 3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
Note: If foreground and background colors are the same, menu
background is transparent.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
Set according to Color Chart:
0 = Black 3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
Note: If foreground and background colors are the same, menu
background is transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT
AVAILABLE” message is displayed when directly accessing a
channel not in the channel scan list available in memory.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, TV automati-
cally tunes to the specified Start Channel.
078 - UPN MSB (UPN Most Significant Byte)
User-programmable number; most significant byte readable by
MPI command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User-programmable number; most significant byte-1 readable by
MPI command. Note: Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User-programmable number; most significant byte-2 readable by
MPI command. Note: Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User-programmable number; least significant byte readable by
MPI command. Note: Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async
port). SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time, which is 64
msec, thus relaxing MPI timing requirements to be compatible
with PC-based Windows-controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be perma-
nent by disabling the blocking hours function. Set to 1 to install
Parental Control restrictions permanently. Set to 0 for user-speci-
fied hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV. Set to 0 to disable
RGB input. Set to 2 to enable for PC and Auto Configure always
enabled. Set to 18 for Auto Configure one time only with power
cord removal and reinsertion.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio is muted if no signal is present.
090 - KEY LOCK
If set to 1, display panel keyboard is locked out and not available
to end user. IR receiver remains functional.
091 - YPrPb2 EN. (HDMI2 Enable)
Set to 0 to disable display panel HDMI2 input. Set to 1 to enable
DTV mode. Set to 2 to enable PC mode.
093 - RJP AVAILABLE (Remote Jack Pack Available)
• 0 = Remote jack pack is not available or disabled.
• 1 = Legacy Model RJPs: HDMI Mode
Enables RJP when an HDMI cable is inserted into RJP. Video
is from HDMI. Audio stream is expected from HDMI source. If
no audio is present, no audio will be heard.
• 2 = Legacy Model RJPs: DVI Mode
Enables RJP when an HDMI cable is inserted into RJP. Video
is from HDMI; however, Audio is from selected audio source,
based on the RJP’s audio hierarchical priority.
• 5 = Scaler Model RJPs: HDMI Mode
Enables RJP when an HDMI cable is inserted into RJP. Video
is from HDMI. Audio stream is expected from HDMI source. If
no audio is present, no audio will be heard.
• 6 = Scaler Model RJPs: DVI Mode
Enables RJP when an HDMI cable is inserted into RJP.
Video is from HDMI; however, Audio is from selected audio
source, based on the RJP ’s audio hierarchical priority.
Notes:
See Reference section, “RJP Model List and Input Auto-sensing
Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040
AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and
6 allow the lodge staff to customize each TV’s RJP setup based
on customer requirements.