Filter
Top Products
27
206-4214
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to restore the factory default settings
of all Installer Menu items. The restoring of factory defaults will
also re-activate the Automated Installation Routine Wizard (see
pages 11 to 14).
Caution: If set to 1, this will restore the factory
defaults and clear the channel lineup, including any
assigned channel icons and custom text labels.
Note: See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded b-
LAN module and the GAME CONTROL/MPI port is only powered
when the TV is turned ON. When the TV is in Standby Mode, the
embedded b-LAN and the GAME CONTROL/MPI port are not
powered.
Note that the TV must be turned ON in order to communicate with
the embedded b-LAN module for conguration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,
the b-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
For specific applications, the RS-232 (DB9) port may be used to
provide +12v/1A external power (for example, to an external MPI
control device). In this case, Installer Menu item 118 POWER
SAVINGS must be set to 9—both the b-LAN module and the
GAME CONTROL/MPI port circuitry are always powered, and the
external power is provided on pin 9 of the RS-232 port.
Note: See Reference section, “b-LAN Setup & Overview,” for
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
119 - DATA CHANNEL
Set to 0 (default) to disable. Set to the RF channel number for
the Data Channel of the Pro:Centric server to enable application
(item 098 PRO:CENTRIC must be set appropriately) and/or TV
E-Z Installation (splash screen, configuration, and firmware) data
downloads.
Note: Pro:Centric application updates are downloaded from the
Pro:Centric server to the TV when the TV is turned ON; however,
TV E-Z Installation updates are downloaded to the TV when the TV
is turned OFF. While E-Z Installation updates are in progress, it is
not possible to turn ON the TV.
Note: The Data Channel is automatically set to “253” if Media
Type is set to “IP” either in the Automated Installation Routine
Wizard or in the IP Environment / Pro:Centric Menu on the TV
(see “Automated Installation Routine Wizard” on pages 11 to 14
or “Pro:Centric Setup” on page 53, respectively) or if the Data
Channel Installer Menu item is set to “IP Address” in the FTG
File Manager, which is used to congure TV CPUs for FTG Mode
operation. It is not possible to change the value to “253” directly in
the Installer Menu.
121 - P:C RF WAKE HR
Set the hour from 0 to 23 for Wake On RF. This item uses the 24-
hour clock format. The value “128” is displayed as “OFF.” Directly
entering 128 turns the Wake On RF feature OFF.
Note: This item is only available in the Installer Menu when item
119 DATA CHANNEL is set to an RF channel 1 to 135.
Note: Items 121 P:C RF WAKE HR and 122 P:C RF WAKE MN
are not available when item 119 DATA CHANNEL is set to 253
(Media Type = IP).
122 - P:C RF WAKE MN
Set the minute from 0 to 59 for Wake On RF.
Note: This item is only available in the Installer Menu when item
119 DATA CHANNEL is set to an RF channel 1 to 135 and when
item 121 P:C RF WAKE HR is set to an hour 0 to 23.
Note: Items 121 P:C RF WAKE HR and 122 P:C RF WAKE MN
are not available when item 119 DATA CHANNEL is set to 253
(Media Type = IP).
Installer Menu (Cont.)