Marantz AV7005 Car Amplifier User Manual


  Open as PDF
of 128
 
52
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
Set up speakers
around items indicate the settings.
1
Set up the
remote control unit
n Set up the operation mode
Press AMP to set the remote control unit
to amplier operation mode.
Press AMP
2
Connect the setup microphone.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Start Auto Setup
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ XT
ENTER Enter RETURN Cancel
When the setup microphone is
connected, the following screen is
displayed.
This section provides the setup methods of speaker systems other than the 7.1-channel system
(with surround back speakers).
For the setup methods of the 7.1-channel system with surround back speakers, see “Simple
version”, “Set up speakers (Audyssey
®
Auto Setup)” (vpage8) of “Simple version”.
First install and connect the speakers to this unit.
Before Auto Setup measurement, the settings shown below can be made.
• Changing the amplifier assignment (Amp Assign)
The signal output from the UNBALANCED and BALANCED PRE OUT SBL/SBR terminals of this unit can
be switched to match your speaker environment. (vpage52 “Set up “Amp Assign””).
• Setting the channels to be used (Channel Select)
If channels that are not to be used are set in advance, measurement for the set channels is skipped, and
measuring time can be reduced (vpage52 “Set up “Channel Select””).
n Audio output from each PRE OUT terminal
PRE OUT Channel
UNBALANCED PRE
OUT terminal
FL/FR C SW1/SW2 SL/SR SBL/SBR HL/HR WL/WR
BALANCED PRE
OUT terminal
FL/FR C SW1/SW2 SL/SR SBL/SBR --- ---
Audio Output Front A Center
Subwoofer 1 /
Subwoofer 2
Surround
Surround
Back*
Front Height /
Front B
Front Wide
*The output audio differs depending on the “Amp Assign” settings.
3
Set up “Amp Assign”
Use ui to select “Amp Assign”,
and then press ENTER.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Set use of surround back ch. for your system
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
MultEQ XT
4
Use o p to select the conguration
of the connected speakers, and then
press RETURN.
Normal
Set when using surround
back, front height or front wide
speakers. In this case, go to step
5.
ZONE2
Set for connecting the speakers
for ZONE2.
ZONE3
Set for connecting the speakers
for ZONE3.
SPKR-C
Set for connecting the tweeter
of the front speaker to the
UNBALANCED and BALANCED
PRE OUT SBL/SBR terminals of
the power amp, and the woofer
of the front speaker to the FL/FR
terminals.
5
Set up “Channel Select”
Use ui to select “Channel Select”,
and then press ENTER.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Skip unused ch’s measurement for timesaving
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
MultEQ XT
6
Use ui to select a channel.
Subwoofer
Select for no subwoofers to be
used. In this case, go to step 7.
Surround
Back
Select for no surround back
speakers to be used. In this case,
go to step 8.
• “Surround Back” can be set when
“Amp Assign” is set to “Normal”.
Front
Height
Select for no front height speakers
to be used. In this case, go to step
9.
• “Front Height” can be set when
“Amp Assign” is set to “Normal”.
Front Wide
Select for no front wide speakers to
be used. In this case, go to step 9.
• “Front Wide” can be set when
“Amp Assign” is set to “Normal”.
7
GWhen “Subwoofer” is selected in
step 6H
Use o p to select the item.
Measure
Set for measuring a subwoofer.
Skip
Set for no measuring of a subwoofer.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
1.AV7005U_ENG.indd 52 2010/08/23 18:32:57
 previous next