Filter
Top Products
23
English
CQ-C9901U/C9801U/C9701U
22
CQ-C9901U/C9801U/C9701U
In the AM mode, only NOISE SUPPRESSION and LOCAL
can be selected.
1
Press [MENU] to
display the menu
display.
For using the remote
control, hold down
[MENU] for 2 sec. or
more.
2
Press [}] or [{] to select a mode to be
adjusted.
3
Press [BAND]
(SET) to adjust.
4
Press [MENU] to confirm the adjust-
ment.
For using the remote control, hold down [MENU]
for 2 sec. or more.
MONO (Monaural)
Noise reduction when the signal strength decreases
: Receiving in stereo (default)
: Receiving in mono and reducing the noise level
LOCAL
Setting when searching for a station
: Searching even for a relatively low-intensity
radio wave station (default)
: Searching only for a high-intensity radio wave
station
NOISE SUPPRESSION
IF filter setting for noise suppression
: Wide range
:
Middle range (
default
)
: Narrow range
AUTO PRESET
You can select 6 or 18 stations for FM presetting with the
use of APM.
:
Presets 6 stations to FM1 to FM3 respectively, that is, 18
stations in total at the same time. This function is useful
for presetting more than 6 stations. (default)
:
Presets 6 stations with good reception to the selected
band from FM1 to FM3. This function is useful for preset-
ting stations in different areas in different bands.
PRESET EDIT
You can arrange the order of the preset stations. Preset
stations can be reordered as you like after executing APM
or the like.
1
Press [}], [{], []] or [[] to select one
station to be interchanged.
2
Press [BAND] to confirm your selection.
3
Press [}], [{], []] or [[] to select the
other station to be interchanged.
4
Press [BAND] to confirm your selection.
●Calling an FM station registered on D•M.
RADIO AUDIO FILTER
You can select the reception status (band) of FM stations
registered on D•M.
: OFF (default)
: High cut level 1
: High cut level 2
Mono/Local Setting (Radio Menu Display)
(MONO/LOCAL)
Radio
Radio
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing [}]
(P·SET) or [{] (P·SET).
Notes:
¡Direct Access can be executed with [1] to [6] buttons
on remote control.
¡You can switch between 6 and 18 for FM presetting
stations.
(
a page 23)
¡Preset stations are changeable. (a page 23)
Auto Preset Memory (APM)
Stations with good receiving conditions are automatically
preset.
1
Select a band.
2
Hold down [BAND]
(APM) for 2 sec.
or more.
The preset stations under best receiving conditions
are received for 5 sec. each after presetting the sta-
tions (SCAN). To stop scanning, press [}] or [{].
Note: New stations overwrite existing saved stations.
Manual station preset
1
Tune in to a station.
2
Hold down [}] or [{] for 2 sec. or
more.
3
Select a preset number by pressing [}]
or [{].
4
Preset the station by holding down [}]
or [{] for 2 sec. or more.
Frequency/preset number blinks once.
Notes:
¡New stations overwrite existing saved stations.
¡In step 2, a station can be registered by holding down
the numeric button [1] to [6] for 2 sec. or more.
¡To stop presetting stations, press [DISP] (Display).
Station Preset
(APM: Auto Preset Memory, P·SET: Preset)
Direct Memory
(D•M: Direct Memory)
You can assign your favorite broadcasting station to the
[D•M] button. As the result of doing that, your favorite
broadcasting station can be received even if the CD mode
or the CD changer mode is activated. (Default: FM 87.9
MHz)
Note: For the use of an FM transmitter, it is useful
for users to register applicable frequencies on D•M
(Direct Memory).
D•M station calling
1
Press [D•M] (Direct Memory).
D•M station writing
1
Select a station you would like to preset.
2
Hold down [D•M] (Direct Memory) for
2 sec. or more.
Lights when the D•M mode is activated.
SRC
CS