Filter
Top Products
12 GB/IE
metal housing dtand the preassembled DIN
assembly bracket until they clearly lock in place.
Ensure that the convex side faces outwards in
each case. Store the installation keys carefully
for future use.
•
Remove the DIN assembly bracket and place it
flush in the DIN assembly cut-out of the
vehicle’s instrument panel.
•
Secure the DIN assembly bracket against removal.
Bend approximately ten tin dog points on both
the upper and lower side of the DIN assembly
bracket from the inside towards the outside.
Please ensure that the DIN assembly bracket is
installed flush in the DIN assembly cut-out.
•
Attach the plastic frame
2completely to the
front of the device
ct.
L
Connection to the car’s loudspeaker
Tip! Use an ISO plug.
• Lead the connecting cables for the speakers
already installed in the vehicle carefully out of
the DIN mounting frame at the front.
•
Hook up the connecting cable of the ISO plug
with the connecting cable of the loudspeakers
fitted in the car with the help of eight biscuit
connectors. Ensure that the connection of the
eight biscuit connectors does not cause any
short circuits and that the fixing screws are
firmly tightened.
•
Hook up the connecting lead of the plug in
el
with the (+) lead for the rear right loudspeaker.
•
Hook up the connecting lead of the plug in
em
with the (–) lead for the rear right loudspeaker.
•
Hook up the connecting lead of the plug in
en
with the (+) lead for the front right loudspeaker.
•
Hook up the connecting lead of the plug in
eo
with the (–) lead for the front right loudspeaker.
•
Hook up the connecting lead of the plug in
ep
with the (+) lead for the front left loudspeaker.
•
Hook up the connecting lead of the plug in
eq
with the (–) lead for the front left loudspeaker.
•
Hook up the connecting lead of the plug in
er
with the (+) lead for the rear left loudspeaker.
•
Hook up the connecting lead of the plug in
es
with the (–) lead for the rear left loudspeaker.
L
Connection with car’s 12 V DC
power supply
c Danger!
· Before hooking up to the car’s 12 V DC power
supply consult the vehicle’s operation manual on
how to observe electrical safety!
·
Ensure that when connecting the 12 V DC power
supply there is no voltage on the vehicle’s
connecting cords. Do not damage any safety
facilities, e.g. board computer and alarm system
of vehicle.
·
Connect the 12 V DC power supply with the 3 x
15 A fuse holders!
· During vehicle installation ensure that the vehicle
is out of operation and is in safe standstill! Turn
off the ignition and bring the vehicle into parking
position with activated hand-brake!
·
During connection, use tools with double-
insulated handle!
·
Avoid electrical short circuits when connecting
to the 12 V DC power supply.
· Connect the car radio with the 12 V DC power
supply while fully protected against humidity!
Tip! Use an ISO plug.
• Ensure that the fault-free flat blade fuse 10 A
eu
is inserted all the way to the catch of the flat
blade fuse socket
et.
• Carefully guide the connecting cable to hook up
the 12 V DC power supply through the front out
of the DIN assembly bracket.
•
Connect the ISO plug with the connecting cables
of the 12 V DC power supply with the 3 x 15 A
fuse holders. Ensure that the connections of
the 3
x 15 A fuse holders do not cause any
short circuits and that the fixing screws are
firmly tightened.
•
Connect the cable for the 12 V DC constant
current plug-in
fmusing a 15 A safety holder
with the vehicle’s connecting cable for the
12
V DC constant current.
• Optional - only if an electric aerial is connected:
Using one 15 A fuse holder each, connect the
cables for the 12 V DC ignition current
foand
electric aerial
fnplug-ins to the connection
Installation
KH2380_Content_UK.indd 12 12.09.2006 11:57:11 Uhr