Filter
Top Products
The System Setup menu
07
50
En
Speaker Distance
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
Important
• When Speaker Distance is selected while MCACC is
set to OFF, the selection screen for the MCACC
memory appears. Select a memory to adjust
manually.
1 Select ‘
Speaker Distance
’ from the Manual SP
Setup menu.
2 Adjust the distance of each speaker using
/
.
You can adjust the distance of each speaker in 1 inch
increments.
3 When you’re finished, press
RETURN
.
You will return to the Manual SP Setup menu.
Tip
• For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.
X-Curve
Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
soundtracks.
1
1 Select ‘
X-Curve
’ from the Manual SP Setup menu.
2 Choose the X-Curve setting you want.
Use / to adjust the setting. The X-Curve is expressed
as a downwards slope in decibels per octave, starting at
2 kHz. The sound becomes less bright as the slope
increases (to a maximum of –3.0dB/oct). Use the
following guidelines to set the X-Curve according to your
room size:
•If you select OFF, the frequency curve will be flat and
the X-Curve has no effect.
3 Select ‘
Return
’, then press
ENTER
to finish.
THX Audio Setting
When the THX Loudness Plus function is used, sound
can be played with the full surround effect even when the
volume is low.
For the most effective results when using the THX
SELECT2 Cinema, THX SELECT2 Music and THX
SELECT2 Games listening modes (see Using the Home
THX modes on page 31) with the Advanced Speaker Array
(ASA) system (see About THX on page 93), it is required
that you make the setting. See Placing the speakers on
page 22 for more on THX speaker placement.
2
1 Select ‘
THX Audio Setting
’ from the Manual SP
Setup menu.
2 Select either
ON
or
OFF
for
THX Loudness Plus
setting.
Note
1 Since the principal is the same, X-Curve isn’t applied when you’re using any of the Home THX modes (see Using the Home THX modes on page 31).
5c.Speaker Distance
Select MCACC memory.
MCACC OFF
M1.MEMORY 1
ENTER:Next
:Cancel
5.Manual SP Setup
:Return
a . Speaker Setting
b . Channel Level
c . Speaker Distance
d . X-Curve
e . THX Audio Setting
5c.Speaker Distance
:Finish
MCACC : M1.MEMORY 1
L 10 ' 00 ''
C [ 0 ' 11 '' ]
R [ 11 ' 09 '' ]
5c.Speaker Distance
:Finish
MCACC : M1.MEMORY 1
SR 0 ' 11 ''
SBR [ 11 ' 09 '' ]
SBL [ 12 ' 05 '' ]
SL [ 13 ' 10 '' ]
SW [ 45 ' 00 '' ]
Room size (ft
2
)
≤400 ≤550 ≤650 ≤800 ≤2200 ≤12000
X-Curve (dB/oct) –0.5 –1 –1.5 –2 –2.5 –3
2 If you don’t have surround back speakers, or have only one surround back speaker or select Speaker B, Front Bi-Amp or ZONE 2 for Surround Back
System, you won’t be able to select this setting (Cannot select shows in the display).
5.Manual SP Setup
:Return
a . Speaker Setting
b . Channel Level
c . Speaker Distance
d . X-Curve
e . THX Audio Setting
63
125
250
500
1k
2k
4k
8k
16k
5d.X-Curve
:Finish
X-Curve -2.0dB/oct
5.Manual SP Setup
:Return
a . Speaker Setting
b . Channel Level
c . Speaker Distance
d . X-Curve
e . THX Audio Setting
5e.THX Audio Setting
Loudness Plus ON
SB SP Position
0 - 1 ft
:Finish
VSX-01TXH_KU.book Page 50 Thursday, March 27, 2008 9:00 PM