Filter
Top Products
-5-
BEFORE OPERATION
Turning the power on and off
Press the z/ON button, the display lights.
To turn the power off, press the z/ON button again, the display turns off,
the clock display remains lit dimly. When economy display mode is needed,
press the /CLOCK/TIMER button, then the clock display goes out.
- When the mains lead is connected to the AC outlet, the unit will respond
to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
DAB section DAB
Remote control CD i, DAB
Selecting the function
Press the FUNCTION button to select the desired function. Each time the
button is pressed, the display changes to select following functions:
CD v Tuner v DAB v LINE v CD v …
The function is automatically selected when CD play is started or when
the DAB button has been pressed.
- When the function selection is changed, CD play is automatically
stopped.
Adjusting the volume
Turn the VOLUME control, or press the VOL – or VOL + button on the
remote control. The volume level appears by numbers (VOL MIN ~ VOL
MAX) on the display.
Bass expander system (Remote control only)
Press the BASS button to enhance the bass sound. “BASS ON” appears
on the display briefly.
Selecting the sound mode (Remote control only)
Press the SOUND button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Connect the mains lead again.
3. Within 5 seconds while pressing the SET UP/RDS MODE button, press
the MEMORY button at the same time.
4. Resume the operation.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
- This unit can play back the CD-R/RW that have
recorded music data as well. However, some CD-R/RWs can not be
played back depending on the recording conditions.
- The CD-R/RW can’t be recorded in this unit.
If the disc is loaded, you can turn the unit on and begin play
immediately by pressing the CD i button.
1. Press the FUNCTION button to select “CD” function. “READING”
appears on the display, then “READING” is replaced by the CD mode
display.
2. Press the OPEN/CLOSE button, disc tray slides out, “OPEN” appears.
3. Place the disc with the label facing
up on the disc tray. (Place only one
disc at a time.)
4. Press the OPEN/CLOSE button
again to close the disc tray. “CLOSE”
appears briefly, then the total
number of tracks and total playing
time on the disc appear.
Note:
If no disc is loaded. “NO DISC” appears. If the disc is loaded with the label
facing downward, or if the disc being loaded can’t be read by the unit,
“UNDISC” appears. If this occurs, load the disc correctly or replace the
damaged disc.
5. Press the CD i button. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
6. Press the n button to end disc play.
When the last track has been played, the player stops automatically.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing surface
of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic sprays
or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the e or f button, then press the CD i
button.
Temporarily stopping play
Press the CD i button. Elapsed playing time blinks and “a” appears.
To resume play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the e button repeatedly
until “6” appears (in the track section) on the display. To skip back to track
3 while track 6 is playing, press the f button repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 6.
Search (forward/reverse)
If the e or f button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.
DAB03UK(En)p05-10-07 05/12/2005, 2:03 PM5