Filter
Top Products
SCD-XA5400ES
14
DVD SERVICE MODE
When the DVD service mode is operated, the following, remote
commander is necessary.
(The DVD service mode cannot be operated by remote commander
to which this machine is attached)
Remote commander (RM-ASP003) (for US, Canadian models):
Part No. 1-479-272-11
Remote commander (RM-ASP004) (for AEP model):
Part No. 1-479-272-21
Note: Above-mentioned remote commander is one example. If it is the
one printed under a remote commander as "DVD", any remote com-
mander can be operated.
1. DVD Service Mode General Description
This mode let you make diagnosis and adjustment easily by us-
ing the remote commander and the TV screen for HDMI input.
The instructions, diagnostic results, etc. are given on the on-screen
display.
Be sure to execute the IOP measurement when a base unit is re-
placed.
2. Enterring DVD Service Mode
Procedure:
1. Press the [?/1] button to turn the power on.
2. Press two buttons of [x] and [A] on the set simultaneously for
3 seconds
3. The message “SERVICE IN” appears on the fl uorescent in-
dicator tube and top menu of the Remocon Diagnosis Menu
appears on the on-screen display on the TV screen for HDMI
input as follows. The model name, IF-con version and Syscon
version are displayed at the bottom of the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name :xxxx_xx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
4. To execute each function, press its number by using numeric
button on the remote commander.
5. To release from this mode, disconnect the power cord.
Note: Don't press the [
?/1
] button when to release from this mode.
Necessarily disconnect the power cord. The set doesn't operate
when turning off power with [
?/1
] button of the set.
3. Executing IOP Measurement
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[V][v] Change Value
[RETURN]Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote com-
mander.
4. Wait until a hexadecimal number appear in the on-screen dis-
play as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: xx
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[V][v] Change Value
[RETURN]Return to previous menu
5. Convert data from hexadecimal to decimal by using conver-
sion table.
6. If the value is smaller than 93 (decimal), then it is OK. How-
ever if the value is higher than 93, then BU (base unit) is defec-
tive and need to be change.
Note: DVD SERVICE MODE is a service mode of super audio
CD.