Alpine CDA-9812RR Car Stereo System User Manual


 
19-EN
Adjusting and Storing the Equalizer Curve
(CDA-9815RB/CDA-9813R only)
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
1
Press EQ to select the EQ mode.
2
Press and hold EQ for at least 2 seconds.
3
Press BAND/TEL. to select your desired
frequency band.
BAND1 BAND2 BAND3 BAND4 BAND5 BAND1
The initial setting of each BAND is as follows.
Frequency
BAND1: 50 Hz, BAND2: 250 Hz, BAND3: 1.0 kHz,
BAND4: 3.2 kHz, BAND5: 10 kHz
Level
BAND1-5: ±0
Width (Q)
BAND1-5: 1
4
Press g or f to select your desired
frequency.
Adjustable frequency bands:
20Hz to 20kHz (in 1/3 octave steps)
5
Turn the Rotary encoder to adjust the level.
6
Press SOURCE/POWER to select your desired
band width (Q).
Adjustable band width: 1, 2, 3.
To store the adjusted curve
1) Press and hold any one of the preset buttons (1
through 6) into which you wish to store the adjusted
curve for at least 2 seconds.
7
To set another channel, repeat steps 3 to 6.
8
After setting, press EQ to return to normal mode.
The frequencies of adjacent bands cannot be adjusted within 4 steps.
EQ mode is automatically cancelled if no buttons are pressed
within 15 seconds.
This function is inoperable when DEFEAT is set to ON (page 17).
When you press DISP/B.OUT, you can switch the Level Indicator
display to the EQ Adjustment display. For details, see “Changing
the Audio Level Display Pattern” (page 7).
Recalling the Stored Equalizer Curve
(CDA-9815RB/CDA-9813R only)
1
Press EQ to select EQ mode.
2
Press and hold EQ for at least 2 seconds.
3
Press any one of the preset buttons (1 through
6) to activate your desired curve.
4
Press EQ to return to normal mode.
EQ mode is automatically cancelled if no operation is performed
within 15 seconds.
This function is inoperable when DEFEAT is set to ON (page 17).
If you do not adjust the factory settings of (FLAT/POPS/ROCK/
NEWS), the factory set display (FLAT/POPS/ROCK/NEWS) is
shown preferentially.
20 Hz -
200 Hz
----
----
----
FLAT, 6,
12, 18,
24 dB/
oct
FLAT, 6,
12, 18,
24 dB/
oct
FLAT, 6,
12, 18,
24 dB/
oct
----
----
0 to
12 dB
0 to
12 dB
0 to
12 dB
Low range
speaker
Rear high
range
speaker
Front high
range
speaker
----
20 Hz -
200 Hz
20 Hz -
200 Hz
Cut-off frequency
(1/3 octave steps)
Slope
Level
HPF LPF HPF LPF
Low range High range
(Different from actual display)
About the Crossover
(CDA-9815RB/CDA-9813R only)
Crossover:
This unit is equipped with an active crossover. The crossover limits
the frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the
frequencies for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass
filter) of each band, and also the slope (how fast the filter rolls off the
highs or lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point,
please consult your authorized Alpine dealer.
2 way mode