Filter
Top Products
51-EN
Adjusting Balance/Fader
Touch [ ] of Balance/Fader, the adjusting screen of
Balance/Fader will be displayed.
Display example for Balance/Fader Screen
Adjusting the Fader
Touch [F] or [R] to adjust the volume of the front and
rear speakers.
Setting range: F15 to R15
• If an optional IMPRINT audio processor (PXA-H100) is connected
to this unit and you have set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/
SUBW.) switch to 2.2ch (3WAY), you cannot adjust the FADER mode.
For details, refer to the Owner’s Manual of PXA-H100.
Adjusting the Balance
Touch [L] or [R] to adjust the sound volume of the left
and right speakers.
Setting range: L15 to R15
Adjusting the Balance/Fader Directly
Touch and move [ ] to a desired setting.
Or touch a desired setting range, and [ ] will move to that
location.
Touch [L] or [R] of Balance and [F] or [R] of Fader for fine-tuning.
Adjusting Bass/Treble
You can change the bass/treble frequency emphasis to
create your own tonal preference.
Touch [ ] to display the Bass/Treble adjusting screen.
• Adjustment cannot be performed when Defeat is set to ON.
• If OFF is set in “Changing MultEQ mode” (page 71) when the
IMPRINT audio processor is connected, the list is not displayed.
Setting the Bass level
You can emphasize or weaken the bass frequency.
Touch [ ] or [ ] of Bass Level to select the desired bass level.
Setting range*
1
: -6 to +6
Setting range: -7 to +7
*
1
Setting value will change according to the level value set in Band 1 of
P-EQ or G-EQ. Refer to
“Adjusting the Parametric Equalizer Curve
(P-EQ)” on page 53 or “Adjusting the Graphic Equalizer Curve (G-
EQ)” on page 53.
Setting the Bass Center Frequency
The displayed bass frequency is emphasized.
Touch [ ] or [ ] of Bass Freq. to select the desired bass center
frequency.
Setting range: 63 Hz, 80 Hz, 100 Hz, 200 Hz
• The operation can be performed only when the P-EQ is selected in
“Setting EQ mode” on page 53.
• Setting value will change according to the frequency value set in
Band 1 of P-EQ. Refer to
“Adjusting the Parametric Equalizer Curve
(P-EQ)” on page 53.
Setting the Bass Bandwidth
Changes the boosted bass bandwidth to wide or narrow.
A wider setting will boost a wide range of frequencies
above and below the center frequency. A narrower
setting will boost only frequencies near the center
frequency.
Touch [ ] or [ ] of Bass Bandwidth to select the desired bass
band width.
Setting range: Wide1 (Narrow) to Wide4 (Wide)
• The operation can be performed only when the P-EQ is selected in
“Setting EQ mode” on page 53.
• Setting value will change according to the bandwidth value set in
Band 1 of P-EQ. Refer to
“Adjusting the Parametric Equalizer Curve
(P-EQ)” on page 53.
Setting the treble level
You can emphasize the treble frequency.
Touch [ ] or [ ] of Treble Level to select the desired treble
level.
Setting range*
2
: -6 to +6
Setting range: -7 to +7
*
2
Setting value will change according to the level value set in Band 5 of
P-EQ or Band 7 of G-EQ. Refer to
“Adjusting the Parametric
Equalizer Curve (P-EQ)” on page 53.
Setting the Treble Center Frequency
The displayed treble frequency is emphasized.
Touch [ ] or [ ] of Treble Freq. to select the desired treble
center frequency.
Setting range: 10 kHz, 12.5 kHz, 16 kHz, 17.5 kHz
• The operation can be performed only when the P-EQ is selected in
“Setting EQ mode” on page 53.
• Setting value will change according to the frequency value set in
Band 5 of P-EQ. Refer to
“Adjusting the Parametric Equalizer Curve
(P-EQ)” on page 53.
A
B
C