Filter
Top Products
73-EN
Adjusting the Frequency
Touch [ ] or [ ] of Freq. to adjust the frequency of the
selected band.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
Adjusting the Level
Touch [ ] or [ ] of Level to adjust the level of selected
band.
Adjustable level: -6 to +6 dB
Setting the Bandwidth
Touch [ ] or [ ] of Q to select the bandwidth.
Adjustable bandwidth: 1, 1.5, 3
4
To adjust another band, repeat step 3 and adjust all
bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• When the parametric EQ is adjusted, the adjustment for graphic EQ
becomes ineffective.
You can modify the equalizer settings to create a response curve more
appealing to your personal taste.
Setting item: G-EQ
1
Select L+R by touching [ ] of G-EQ.
When parametric EQ is set to L+R, this setting will be turned
off.
2
Touch [ ] of G-EQ after selecting L+R.
The G-EQ list screen appears.
3
Adjust the G-EQ to your preference.
Adjusting the Band
Touch [ ] or [ ] of Band to select the band to be adjusted.
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
Adjusting the Level
Touch [ ] or [ ] of Level to adjust the level of selected
band.
Adjustable output level: -6 to +6 dB
4
To adjust another band, repeat step 3, and then
adjust all bands.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
You can change the unit, (cm or inch) of time correction.
Touch [ ] or [ ] of T.Corr Parameter to select cm or Inch.
Setting item: T.Corr Parameter
cm Inch
Before performing the following procedures, refer to “About Time
Correction” (page 75).
Setting item: Time Correction
1
Touch [ ] of Time Correction.
The Time Correction adjustment screen appears.
2
Adjust the distance (0.0 to 336.6 cm) of a desired
speaker by touching the respective [
] or [ ]
button.
L = (distance to farthest speaker) –
(distance to other speakers)
Refer to “Time Correction Value List” on page 75.
3
Repeat step 2 to set another speaker.
Set these values to achieve simultaneous sound
propagation to the listening position from all speakers.
Before performing the following procedures, refer to “About the
Crossover” (page 76).
Setting item: X-Over
1
Touch [ ] or [ ] of X-Over to select L+R or L/R.
2
Touch [ ] of X-Over.
A speaker list on the X-Over screen is displayed.
3
Touch [ ] of the band to be adjusted.
The screen changes to the X-Over screen to be adjusted.
4.2ch (FRONT/REAR/SUBW.) System / (L+R)
Setting contents:
Low (SUB-W) / Mid (REAR) / High (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / (L/R)
Setting contents:
Low (SUB-W)-L / Low (SUB-W)-R / Mid (REAR)-L /
Mid (REAR)-R / High (FRONT)-L / High (FRONT)-R
Adjusting the Graphic Equalizer Curve
(G-EQ)
Setting the Time Correction Unit (T.Corr
Parameter)
cm: The unit of time correction is cm.
Inch: The unit of time correction is Inch.
Adjusting the Time Correction
Adjusting the Crossover Settings (X-OVER)
L+R: Sets the same adjustment values for the left and right
channels.
L/R: Different adjustment values can be set for the left and
right channels.
4.2ch (FRONT/REAR/SUBW.) System